{"annotations":[{"start_s":0.0,"end_s":5.692,"action":"Switched to AutoCAD and entered the UN command, opening the Drawing Units dialog.","intent":"Open drawing unit settings.","app":"AutoCAD","details":"Drawing1.dwg was displayed with an empty model space."},{"start_s":5.692,"end_s":17.812,"action":"Opened the Length Type dropdown in Drawing Units and clicked through unit-setting controls, leaving the dialog open.","intent":"Adjust drawing units.","app":"AutoCAD","details":"The Drawing Units dialog showed Decimal length units, Decimal Degrees angles, millimeter insertion scale, and the Length Type menu expanded."},{"start_s":17.812,"end_s":27.922,"action":"Returned to the drawing, started the RECTANG command, and positioned the cursor to specify the first corner.","intent":"Create a rectangle.","app":"AutoCAD","details":"The command line prompted for the first rectangle corner."},{"start_s":27.922,"end_s":32.764,"action":"Entered dynamic dimensions for the rectangle and specified the opposite corner, producing a rectangular outline in the drawing.","intent":"Define the rectangle dimensions.","app":"AutoCAD","details":"The rectangle remained active while the opposite-corner prompt displayed numeric input."},{"start_s":32.764,"end_s":42.238,"action":"Continued entering dynamic input values for the rectangle and pressed Enter to complete the opposite-corner specification.","intent":"Complete the rectangle.","app":"AutoCAD","details":"A larger horizontal rectangle was visible while the opposite-corner prompt remained active."},{"start_s":42.238,"end_s":59.615,"action":"Navigated the drawing with middle-button clicks and scrolling, then started OFFSET and selected the rectangle; entered an offset distance prompt without completing the offset.","intent":"Offset the rectangle.","app":"AutoCAD","details":"The view changed to show a vertical rectangle, and the command line prompted for an offset distance or Through."},{"start_s":59.615,"end_s":73.119,"action":"Entered offset values through the dynamic input, confirmed them, and clicked in the drawing while AutoCAD remained in the Offset command; then canceled one prompt.","intent":"Continue creating parallel geometry with the Offset command.","app":"AutoCAD","details":"Drawing1.dwg showed a rectangular outline and an active offset prompt."},{"start_s":73.119,"end_s":83.219,"action":"Entered an offset distance of 10, confirmed it, and selected a vertical line; AutoCAD displayed the resulting parallel line and prompted for another side selection.","intent":"Offset the selected vertical edge by a specified distance.","app":"AutoCAD","details":"The Offset command remained active for repeated selections."},{"start_s":83.219,"end_s":97.547,"action":"Entered an offset distance of 4.5, confirmed it, and continued selecting points and adjusting the view while AutoCAD processed the offset; a new parallel rectangular edge appeared.","intent":"Add another precisely spaced parallel edge to the drawing.","app":"AutoCAD","details":"AutoCAD remained in the Offset command; a WhatsApp notification appeared briefly."},{"start_s":97.547,"end_s":103.773,"action":"Confirmed the pending offset input, adjusted the view, and clicked the drawing to continue the active Offset command.","intent":"Continue placing another offset feature in the drawing.","app":"AutoCAD","details":"The drawing showed multiple nested rectangular outlines and vertical divisions."},{"start_s":103.773,"end_s":110.429,"action":"Entered and confirmed another 4.5 offset value, adjusted the view, and clicked the drawing to continue the Offset command.","intent":"Create an additional evenly spaced parallel line.","app":"AutoCAD","details":"The active prompt requested another object to offset."},{"start_s":110.429,"end_s":117.618,"action":"Entered and confirmed an offset distance of 5'10\", then clicked a horizontal area of the drawing; AutoCAD displayed the new horizontal offset line and continued prompting for another object.","intent":"Add a horizontal offset at the specified architectural distance.","app":"AutoCAD","details":"Drawing1.dwg remained in the active Offset command with multiple rectangular divisions visible."},{"start_s":117.618,"end_s":124.837,"action":"Entered a 0.5-inch offset distance, confirmed it, and navigated the drawing while the OFFSET command remained active.","intent":"Create repeated offsets in the drawing using a 0.5-inch distance.","app":"AutoCAD","details":"The drawing view zoomed out and the command line continued to request an object or point to offset."},{"start_s":124.837,"end_s":129.135,"action":"Entered a 1-foot-6-inch offset distance, confirmed it, and adjusted the drawing view while OFFSET remained active.","intent":"Set a larger offset distance for the next drawing operation.","app":"AutoCAD","details":"The command line showed the 1'6\" distance and then returned to selecting an object to offset."},{"start_s":129.135,"end_s":133.77,"action":"Entered a 0.5-inch offset distance, confirmed it, canceled the active offset operation, and began entering another command before canceling again.","intent":"Continue offset construction and reset the command state.","app":"AutoCAD","details":"The drawing retained the rectangular line layout; the command line showed Cancel after the OFFSET operation."},{"start_s":133.77,"end_s":146.198,"action":"Re-entered and confirmed the R command, dragged across the drawing to select or modify geometry, then canceled the active trim/extend operation and adjusted the view.","intent":"Modify existing drawing geometry with a selection-based editing command.","app":"AutoCAD","details":"The command line showed a next fence point and trim-or-shift selection prompts before cancellation."},{"start_s":146.198,"end_s":156.38,"action":"Entered and confirmed a 2-foot offset distance, navigated the drawing, and selected another drawing location while OFFSET remained active.","intent":"Apply or prepare another large offset to the drawing geometry.","app":"AutoCAD","details":"The command line displayed an offset distance of 12 feet and then requested an object to offset."},{"start_s":156.38,"end_s":164.191,"action":"Entered a 0.5-inch offset distance, confirmed it, zoomed and panned the drawing, and clicked near the geometry while OFFSET continued requesting an object.","intent":"Continue creating offsets at the specified distance.","app":"AutoCAD","details":"The drawing view was zoomed in on the rectangular line layout and the command line still showed OFFSET object-selection prompts."},{"start_s":164.191,"end_s":171.908,"action":"Entered 1'4\" and confirmed the offset distance, then clicked in the drawing to continue the active OFFSET command and entered 4.","intent":"Specify an offset distance and select the side for the next offset.","app":"AutoCAD","details":"The drawing remained in OFFSET, prompting to select an object or point."},{"start_s":171.908,"end_s":185.95,"action":"Entered .5\" and confirmed it, then clicked in the drawing while OFFSET remained active and entered 1.","intent":"Apply another offset distance and continue selecting geometry for the offset operation.","app":"AutoCAD","details":"The OFFSET prompt continued to request the side or next object."},{"start_s":185.95,"end_s":191.173,"action":"Entered 0'4\" and confirmed the offset distance, then clicked in the drawing and entered 4.","intent":"Create another four-inch offset and continue the active drafting operation.","app":"AutoCAD","details":"AutoCAD continued displaying the OFFSET selection prompt."},{"start_s":191.173,"end_s":198.938,"action":"Entered .5\" and confirmed it, then used middle-button clicks to navigate the drawing, clicked to continue OFFSET, and entered 1.","intent":"Continue the offset sequence while navigating to another area of the drawing.","app":"AutoCAD","details":"The OFFSET command remained active with the drawing view repositioned."},{"start_s":198.938,"end_s":204.509,"action":"Entered 2' and confirmed it, adjusted the drawing view with scrolling, clicked to continue OFFSET, and entered 4.","intent":"Specify a two-foot offset and continue the drafting operation in the repositioned view.","app":"AutoCAD","details":"The command line continued to show the OFFSET prompt."},{"start_s":204.509,"end_s":208.674,"action":"Entered .5\" and confirmed it, canceled the active OFFSET command with Escape, then began typing TR and submitted the command.","intent":"End the offset sequence and start a new AutoCAD command.","app":"AutoCAD","details":"The command line showed the offset operation canceled, and dynamic input displayed TR."},{"start_s":208.674,"end_s":218.195,"action":"Activated AutoCAD, adjusted the window and view, and continued the active TRIM command by dragging and selecting drawing geometry.","intent":"Trim or extend selected drawing lines.","app":"AutoCAD","details":"The command line prompted to select an object to trim or shift-select to extend, then requested the next fence point."},{"start_s":218.195,"end_s":228.266,"action":"Canceled the active TRIM operation, adjusted the view, and started the MEASUREGEOM distance command before specifying a first point.","intent":"Measure a distance in the drawing.","app":"AutoCAD","details":"The command line showed that the previous command was undone or canceled and ended at “MEASUREGEOM Specify first point.”"},{"start_s":228.266,"end_s":238.282,"action":"Selected points in the drawing to continue the distance measurement and left the command awaiting a second point while adjusting the view.","intent":"Measure the distance between two drawing points.","app":"AutoCAD","details":"The command line displayed “MEASUREGEOM Specify second point” and the canvas showed a live distance readout."},{"start_s":238.282,"end_s":252.097,"action":"Continued and then canceled the distance measurement, opened the Measure menu, and returned to the drawing with the geometry unchanged.","intent":"Inspect measurement options or measure drawing geometry.","app":"AutoCAD","details":"The Measure menu visibly listed Quick, Distance, Radius, Angle, Area, and Volume."},{"start_s":252.097,"end_s":271.916,"action":"Entered a command through dynamic input, adjusted the view, opened the Measure menu, and canceled the active operation before beginning a new command search for “T.”","intent":"Switch between measurement and editing commands.","app":"AutoCAD","details":"Dynamic input showed a TR command suggestion list including TRIM, and the Measure menu remained available during the interval."},{"start_s":271.916,"end_s":282.434,"action":"Entered the command through dynamic input, adjusted the view, and dragged across the drawing to select or trim geometry.","intent":"Trim or extend drawing lines.","app":"AutoCAD","details":"The command line showed TRIM with cutting-edge and crossing options, and the prompt requested an object to trim or shift-select to extend."},{"start_s":282.434,"end_s":295.306,"action":"Adjusted the AutoCAD window and view, interacted with the drawing using middle- and left-clicks, and canceled the active TRIM command with Escape.","intent":"Manipulate and inspect the drawing while attempting a trim operation.","app":"Autodesk AutoCAD 2021","details":"The drawing remained visible with the TRIM prompt active until cancellation."},{"start_s":295.306,"end_s":312.501,"action":"Entered and confirmed a command, navigated the drawing with middle-clicks and scrolling, dragged across the drawing, and canceled the active command with Escape.","intent":"Navigate and modify or inspect geometry in the AutoCAD drawing.","app":"Autodesk AutoCAD 2021","details":"The view changed to show more of the floor-plan geometry; the command line continued to show TRIM prompts before cancellation."},{"start_s":312.501,"end_s":319.659,"action":"Opened the AutoCAD application menu, selected Save As, and began editing the drawing filename in the Save Drawing As dialog.","intent":"Save the current drawing under a new filename.","app":"Autodesk AutoCAD 2021","details":"The Save Drawing As dialog opened in Documents with Drawing1 in the file name field."},{"start_s":319.659,"end_s":324.927,"action":"Edited the Save Drawing As filename field by deleting and entering characters, leaving a filename suggestion list open.","intent":"Set the output filename for the drawing.","app":"Autodesk AutoCAD 2021","details":"The filename field showed a partial entry beginning with “g”, with matching drawing names listed below."},{"start_s":324.927,"end_s":335.872,"action":"Entered the filename “G+1 PLAN@02” in the Save Drawing As dialog and clicked the Save button.","intent":"Save the drawing as G+1 [hidden]","app":"Autodesk AutoCAD 2021","details":"The dialog displayed the completed filename before the save action."},{"start_s":335.872,"end_s":345.362,"action":"Returned to AutoCAD with the drawing renamed to G+1 [hidden], navigated the view with middle-clicks, and clicked within the drawing area.","intent":"Continue working in the newly saved drawing.","app":"Autodesk AutoCAD 2021","details":"The saved drawing opened and displayed the floor-plan geometry; subsequent window resizing reduced the AutoCAD window."},{"start_s":345.362,"end_s":358.327,"action":"Resized and repositioned the AutoCAD window repeatedly while the OFFSET command remained active, then entered 9 as the offset distance.","intent":"Set an offset distance in the drawing.","app":"AutoCAD","details":"The drawing remained visible with the OFFSET prompt awaiting input."},{"start_s":358.327,"end_s":369.368,"action":"Confirmed the offset distance of 9, selected an object and a side for offsetting, and left OFFSET prompting for another object.","intent":"Create an offset line in the floor-plan drawing.","app":"AutoCAD","details":"A new horizontal line appeared in the lower portion of the plan."},{"start_s":369.368,"end_s":377.344,"action":"Confirmed the previous offset-side prompt, adjusted the view with scrolling and window movement, and continued at the OFFSET object-selection prompt.","intent":"Continue placing offsets in the drawing.","app":"AutoCAD","details":"The plan view shifted while OFFSET remained active."},{"start_s":377.344,"end_s":382.72,"action":"Entered the distance 13'6\" and confirmed it, then selected an offset side and returned to the object-selection prompt.","intent":"Apply a second, dimensioned offset to the plan.","app":"AutoCAD","details":"The command history shows the entered distance as 13'6\"."},{"start_s":382.72,"end_s":392.72,"action":"Exited the active offset prompt, started TRIM, navigated and zoomed the drawing, and selected geometry for trimming.","intent":"Trim intersecting or excess lines in the floor plan.","app":"AutoCAD","details":"TRIM displayed the prompt to select an object to trim or shift-select to extend."},{"start_s":392.72,"end_s":411.208,"action":"Continued selecting and trimming drawing geometry while panning and zooming, then canceled TRIM and left the drawing in a broader plan view.","intent":"Clean up the floor-plan linework.","app":"AutoCAD","details":"The command line ended with a canceled TRIM prompt and returned to the command input state."},{"start_s":411.208,"end_s":417.657,"action":"Entered and confirmed an AutoCAD command, adjusted the drawing view through dragging, canceled an active operation, and began entering an offset distance.","intent":"Modify or inspect the floor-plan geometry using AutoCAD commands.","app":"Autodesk AutoCAD 2021","details":"The drawing remained visible and the command line showed OFFSET requesting a distance."},{"start_s":417.657,"end_s":425.419,"action":"Completed the offset-distance entry, canceled the OFFSET command, and navigated the floor-plan view with middle-button panning and zooming.","intent":"Set up or inspect a different area of the floor plan after canceling the offset operation.","app":"Autodesk AutoCAD 2021","details":"The command line showed the offset prompt and then cancellation; the view shifted to a narrower portion of the plan."},{"start_s":425.419,"end_s":435.407,"action":"Repositioned the AutoCAD view repeatedly, canceled the pending command, and left the floor plan displayed at a broader view.","intent":"Adjust the drawing view for inspection.","app":"Autodesk AutoCAD 2021","details":"No confirmed geometry edit was visible; the command line still reflected the canceled offset workflow."},{"start_s":435.407,"end_s":445.535,"action":"Started a measurement operation, selected a first point, and left AutoCAD waiting for a second point before canceling.","intent":"Measure a distance in the floor plan.","app":"Autodesk AutoCAD 2021","details":"The command line showed MEASUREGEOM requesting a second point, with a displayed distance of about 13'-8\" before cancellation."},{"start_s":445.535,"end_s":455.493,"action":"Navigated the drawing with middle-button panning and scrolling, then clicked near the upper-right area while the measurement prompt remained canceled.","intent":"Inspect another portion of the floor plan.","app":"Autodesk AutoCAD 2021","details":"The floor-plan view shifted vertically; no new command or confirmed geometry change was visible."},{"start_s":455.493,"end_s":474.424,"action":"Canceled the remaining measurement workflow, panned and scrolled through the floor plan, and ended with the drawing centered on a lower section.","intent":"Review and reposition the floor-plan view.","app":"Autodesk AutoCAD 2021","details":"The command line returned to an idle state by the end of the span."},{"start_s":474.424,"end_s":484.543,"action":"Entered R and pressed Enter, then dragged and clicked repeatedly in the AutoCAD drawing while the TRIM command prompted for another fence point.","intent":"Trim or modify selected drawing edges using a fence selection.","app":"AutoCAD","details":"The command line displayed “TRIM Specify next fence point or [Undo].”"},{"start_s":484.543,"end_s":494.775,"action":"Continued the TRIM fence interaction, panned or zoomed the drawing with middle-button actions, then canceled the command with Escape.","intent":"Inspect the drawing and stop the active trim operation.","app":"AutoCAD","details":"The command history showed “*Cancel*” after prompts to select objects to trim."},{"start_s":494.775,"end_s":510.355,"action":"Panned and zoomed across the floor-plan drawing with middle-button actions, then initiated MEASUREGEOM and left AutoCAD prompting for the first point.","intent":"Navigate to a drawing area and begin measuring geometry.","app":"AutoCAD","details":"The status prompt read “MEASUREGEOM Specify first point.”"},{"start_s":510.355,"end_s":518.264,"action":"Entered a distance value of 9'6\" for MEASUREGEOM, canceled the measurement, and started an OFFSET operation that prompted for the second point.","intent":"Measure or offset geometry using a specified distance.","app":"AutoCAD","details":"The command line showed MEASUREGEOM distance input followed by OFFSET prompting for the second point."},{"start_s":518.264,"end_s":528.212,"action":"Entered 9'6\" as the OFFSET distance, selected a drawing object, and positioned the cursor to specify the side for the offset.","intent":"Create a parallel offset at the specified distance.","app":"AutoCAD","details":"The OFFSET prompt displayed “Specify point on side to offset.”"},{"start_s":528.212,"end_s":538.015,"action":"Panned and zoomed the drawing, then continued the active MEASUREGEOM operation by selecting points while AutoCAD displayed a 9'-3\" measurement.","intent":"Measure distances in the floor-plan drawing.","app":"AutoCAD","details":"The command line remained at “MEASUREGEOM Specify second point or [Multiple points].”"},{"start_s":538.015,"end_s":548.332,"action":"Resized and repositioned the AutoCAD window, navigated the drawing view, and activated MEASUREGEOM Distance. Began specifying the first point, then canceled the measurement after zooming or panning.","intent":"Measure a distance in the floor-plan drawing.","app":"AutoCAD","details":"The command line shows MEASUREGEOM Distance with the first point requested, followed by cancellation."},{"start_s":548.332,"end_s":557.481,"action":"Panned and zoomed the floor-plan view, then repositioned the AutoCAD window and left the command area ready for another operation.","intent":"Adjust the drawing view and prepare for continued editing.","app":"AutoCAD","details":"No completed geometry change is visible; the prior measurement prompt remains canceled."},{"start_s":557.481,"end_s":575.562,"action":"Navigated around the drawing, canceled the active command, and started a STRETCH operation by selecting or dragging near the plan geometry. Canceled the stretch before completing it and returned to the drawing view.","intent":"Attempt to adjust existing floor-plan geometry.","app":"AutoCAD","details":"The command line shows STRETCH and then Command: *Cancel*."},{"start_s":575.562,"end_s":585.143,"action":"Entered a command shortcut and confirmed it, then dragged repeatedly across the drawing while AutoCAD displayed the STRETCH prompt. Continued manipulating the view or selection without a visible completed result.","intent":"Stretch or reposition selected drawing geometry.","app":"AutoCAD","details":"AutoCAD remains in an active STRETCH operation with the prompt to specify the stretch point."},{"start_s":585.143,"end_s":595.021,"action":"Continued dragging in the drawing while AutoCAD displayed the TRIM prompt, then clicked and canceled the operation. Adjusted the view afterward.","intent":"Trim selected floor-plan edges.","app":"AutoCAD","details":"The command line shows TRIM with the prompt to select an object to trim or extend, followed by Escape."},{"start_s":595.021,"end_s":609.1,"action":"Navigated and resized the AutoCAD window, then activated MEASUREGEOM Distance and began specifying a first point. Canceled the measurement without selecting a second point.","intent":"Measure a distance in the floor-plan drawing.","app":"AutoCAD","details":"The final view shows MEASUREGEOM requesting the first point, with the second-point prompt canceled."},{"start_s":609.1,"end_s":625.083,"action":"Canceled the active line and stretch operations, navigated the AutoCAD view, and began a new line command before switching into stretch-related interaction.","intent":"Edit and inspect the floor-plan geometry using AutoCAD drafting commands.","app":"AutoCAD","details":"The command line shows LINE activity followed by a canceled STRETCH command; the view changed substantially during navigation."},{"start_s":625.083,"end_s":635.844,"action":"Entered the TRIM command, then dragged across the drawing and selected a point while AutoCAD prompted to select an object to trim or extend.","intent":"Trim selected portions of the floor-plan geometry.","app":"AutoCAD","details":"The command line visibly shows TRIM with cutting-edges and Crossing options."},{"start_s":635.844,"end_s":646.098,"action":"Continued dragging and clicking within the drawing while TRIM remained active, then navigated the view with additional middle-button actions and scrolling.","intent":"Continue selecting geometry for trimming and reposition the drawing view.","app":"AutoCAD","details":"AutoCAD continued prompting for the next fence point or an object to trim."},{"start_s":646.098,"end_s":657.549,"action":"Continued the TRIM selection with a long drag and click, navigated to a wider floor-plan view, canceled the active command, and issued a save command.","intent":"Finish the trimming pass, save the drawing, and review the resulting layout.","app":"AutoCAD","details":"The command line shows _qsave followed by a command prompt; a recorder window preview appeared near the end."},{"start_s":657.549,"end_s":664.873,"action":"Switched briefly to the recorder window, pressed Escape, scrolled and middle-clicked, then returned to AutoCAD and canceled the active command.","intent":"Briefly inspect or interact with the recorder window before resuming the drawing.","app":"Screen recorder","details":"The evidence still shows the AutoCAD floor plan; system state changes and privacy masking occurred during the app transition."},{"start_s":664.873,"end_s":674.906,"action":"Entered the R command and confirmed it, then dragged and clicked across the AutoCAD floor plan while the TRIM prompt remained active, with additional scrolling and middle-button navigation.","intent":"Continue editing and trimming the floor-plan geometry.","app":"AutoCAD","details":"The command line shows repeated prompts for the next fence point and selecting objects to trim or extend."},{"start_s":674.906,"end_s":688.366,"action":"Manipulated the AutoCAD view with panning, zooming, and middle-click navigation while the TRIM command remained active; pressed Escape and began entering another command.","intent":"Inspect the floor-plan geometry and continue editing with AutoCAD commands.","app":"Autodesk AutoCAD","details":"The drawing view changed from a close-up to a zoomed-out floor plan, with the prompt to select an object to trim visible."},{"start_s":688.366,"end_s":694.733,"action":"Entered R and confirmed it, then navigated and zoomed the drawing while the TRIM prompt remained active; pressed Escape to cancel and began entering L.","intent":"Adjust the drawing view and switch from the current trim operation to another command.","app":"Autodesk AutoCAD","details":"The view moved across the floor plan, and the command line ended in a canceled TRIM state."},{"start_s":694.733,"end_s":698.966,"action":"Confirmed the command input, clicked in the drawing, and started the LINE command at a corner; entered R and then canceled the operation.","intent":"Attempt to create or modify line geometry near the plan corner.","app":"Autodesk AutoCAD","details":"The LINE prompt showed “Specify first point,” then the command was canceled."},{"start_s":698.966,"end_s":708.794,"action":"Entered and confirmed commands, clicked and dragged around the plan, and navigated the view; canceled the active operation and opened the Modify ribbon panel.","intent":"Edit and inspect the floor-plan geometry using modify tools.","app":"Autodesk AutoCAD","details":"The drawing was zoomed to show the full plan, and the command line displayed a canceled TRIM operation."},{"start_s":708.794,"end_s":713.033,"action":"Selected the JOIN tool from the Modify panel and activated it; left AutoCAD prompting for a source object or multiple objects to join.","intent":"Join adjacent line segments in the floor-plan drawing.","app":"Autodesk AutoCAD","details":"The visible prompt read “Select source object or multiple objects to join at once.”"},{"start_s":713.033,"end_s":718.5,"action":"Navigated and zoomed the drawing, then selected geometry for JOIN; AutoCAD reported that two lines were joined into one line, and began entering T.","intent":"Combine selected floor-plan segments and continue with another editing command.","app":"Autodesk AutoCAD","details":"The command history showed “Select objects to join: 1 found, 2 total” and “2 lines joined into 1 line.”"},{"start_s":718.5,"end_s":731.452,"action":"Entered and confirmed the R command, navigated and zoomed/panned around the floor-plan drawing, then used the active TRIM command to select or drag across geometry before canceling it.","intent":"Modify or inspect floor-plan linework with TRIM.","app":"Autodesk AutoCAD 2021","details":"The command line ended with TRIM active and then *Cancel*."},{"start_s":731.452,"end_s":741.144,"action":"Entered and confirmed R, navigated the drawing with zoom/pan gestures, and dragged across the floor-plan geometry while the TRIM prompt remained active.","intent":"Continue trimming or inspecting drawing geometry.","app":"Autodesk AutoCAD 2021","details":"The visible prompt requested an object to trim or shift-select to extend."},{"start_s":741.144,"end_s":751.627,"action":"Navigated and zoomed around the floor plan, dragged across drawing areas during the active TRIM command, then canceled the operation and issued a save command.","intent":"Review the drawing and save the current AutoCAD file.","app":"Autodesk AutoCAD 2021","details":"The command line showed _qsave after TRIM was canceled."},{"start_s":751.627,"end_s":755.817,"action":"Typed TOOL through the AutoCAD command input, resulting in an unknown-command warning for TOOL.","intent":"Attempt to open a tool-related AutoCAD command.","app":"Autodesk AutoCAD 2021","details":"The command line reported: Unknown command \"TOOL\"."},{"start_s":755.817,"end_s":762.133,"action":"Canceled the unknown command, typed TOOL again through dynamic input, and returned to the drawing without executing a valid command.","intent":"Retry and then dismiss the tool-related command entry.","app":"Autodesk AutoCAD 2021","details":"The command line ended with *Cancel*."},{"start_s":762.133,"end_s":766.51,"action":"Opened the Tool Palettes, briefly manipulated the palette window, and left the Architectural palette visible with Imperial and Metric sample tools.","intent":"Access architectural tool palette samples for potential insertion or use.","app":"Autodesk AutoCAD 2021","details":"The visible palette included Door, Window, Aluminum Window, Fluorescent, Stud, Toilet, Trees, and Vehicles samples."},{"start_s":766.51,"end_s":786.053,"action":"Returned to the AutoCAD drawing, manipulated the window and view, and initiated a MOVE command. Selected one object and left AutoCAD prompting for the move displacement.","intent":"Move a selected drawing object.","app":"AutoCAD","details":"The command line shows MOVE with one object found and a prompt for the second point or displacement."},{"start_s":786.053,"end_s":790.508,"action":"Resized and repositioned the AutoCAD window, then continued the MOVE command by specifying a base point and leaving the second-point/displacement prompt active.","intent":"Continue positioning the selected object with MOVE.","app":"AutoCAD","details":"The drawing remains visible while the command line prompts for the second point or displacement."},{"start_s":790.508,"end_s":795.056,"action":"Paused in AutoCAD with the MOVE command still active and the dynamic input field visible, then switched to Windows Explorer.","intent":"Leave the pending AutoCAD operation and open another application.","app":"AutoCAD","details":"No completed move is visible before the switch to Windows Explorer."},{"start_s":795.056,"end_s":802.42,"action":"Returned to AutoCAD, adjusted the view and window, and started MIRROR; selected an object and left the command at the object-selection prompt.","intent":"Mirror a selected drawing object.","app":"AutoCAD","details":"The command line shows MIRROR Select objects, with the floor-plan drawing visible."},{"start_s":802.42,"end_s":807.909,"action":"Continued MIRROR by defining the first point and positioning the second point of the mirror line, with orthogonal mode indicated.","intent":"Define the mirror line for the selected object.","app":"AutoCAD","details":"Dynamic input shows the prompt for the second point of the mirror line."},{"start_s":807.909,"end_s":815.184,"action":"Completed the mirror-line input and reviewed the result, then zoomed and began another object-selection operation; the command line ended on MOVE Select objects.","intent":"Apply or inspect the mirror operation and begin a subsequent move.","app":"AutoCAD","details":"The drawing is shown enlarged, with the command line prompting to select objects for MOVE."},{"start_s":815.184,"end_s":825.163,"action":"Continued the AutoCAD MOVE command, selected one object, specified a base point, and positioned the cursor for the second point while the floor plan view changed.","intent":"Move a selected floor-plan element to a new location.","app":"AutoCAD","details":"MOVE remained active at the end of the span."},{"start_s":825.163,"end_s":838.265,"action":"Completed the pending move, zoomed and navigated around the floor plan, then began a COPY operation and selected two objects.","intent":"Copy selected floor-plan elements.","app":"AutoCAD","details":"COPY was awaiting further input at the end."},{"start_s":838.265,"end_s":851.834,"action":"Continued the COPY command in multiple-copy mode, specified a base point, and positioned a copied element at a new location in the plan.","intent":"Create repeated copies of selected floor-plan elements.","app":"AutoCAD","details":"COPY was still awaiting an array or exit choice at the end."},{"start_s":851.834,"end_s":862.372,"action":"Selected objects and started SCALE, specified a base point, zoomed or navigated the drawing, and saved the drawing before leaving the scale operation active.","intent":"Scale selected floor-plan geometry and preserve the drawing.","app":"AutoCAD","details":"SCALE was awaiting a scale factor or related input."},{"start_s":862.372,"end_s":872.776,"action":"Selected an object and started ROTATE, specified a base point, and positioned the cursor for the rotation angle.","intent":"Rotate a selected floor-plan element.","app":"AutoCAD","details":"ROTATE was awaiting the rotation angle at the end."},{"start_s":872.776,"end_s":889.166,"action":"Continued editing the floor plan with COPY and SCALE commands, selecting and positioning geometry while zooming or panning between views.","intent":"Duplicate and resize floor-plan elements.","app":"AutoCAD","details":"SCALE was awaiting object selection at the end."},{"start_s":889.166,"end_s":898.64,"action":"Switched to AutoCAD, adjusted the view and window, and continued the active SCALE command by specifying a base point and scale factor; zoomed out to show more of the floor plan.","intent":"Scale the selected drawing geometry and review the resulting plan view.","app":"AutoCAD","details":"The command line showed SCALE with one object selected and then prompted for a scale factor."},{"start_s":898.64,"end_s":908.609,"action":"Entered R and confirmed it, then zoomed and panned the floor plan; activated TRIM and moved across the drawing while the prompt asked for an object to trim or extend.","intent":"Set up and apply a drawing edit using the TRIM command.","app":"AutoCAD","details":"The visible TRIM prompt indicated cutting edges and requested an object to trim or shift-select to extend."},{"start_s":908.609,"end_s":918.898,"action":"Selected and dragged across drawing geometry, canceled the active interaction, saved the drawing, and zoomed out to review the plan.","intent":"Modify or inspect the floor-plan geometry and save the drawing.","app":"AutoCAD","details":"The command line showed _qsave after the interaction was canceled."},{"start_s":918.898,"end_s":929.058,"action":"Zoomed and panned to a lower portion of the floor plan, then interacted with the drawing area and adjusted the AutoCAD window.","intent":"Navigate to and inspect a specific area of the floor plan.","app":"AutoCAD","details":null},{"start_s":929.058,"end_s":934.67,"action":"Continued navigating and zooming the drawing, then started MEASUREGEOM and specified a first point followed by a second point to measure a distance.","intent":"Measure a distance in the floor-plan drawing.","app":"AutoCAD","details":"The command line showed MEASUREGEOM and prompted for the second point or multiple points."},{"start_s":934.67,"end_s":951.056,"action":"Canceled the measurement interaction, restored the AutoCAD window, and typed L to begin a new command; the drawing remained in a close-up floor-plan view.","intent":"End the measurement and initiate the next drawing command.","app":"AutoCAD","details":"The final visible prompt was from the measurement workflow, while L was entered at the end of the span."},{"start_s":951.056,"end_s":965.017,"action":"Activated the LINE command, specified a first point, and positioned the cursor to define the next segment while adjusting the AutoCAD window.","intent":"Continue drawing a line in the floor-plan drawing.","app":"AutoCAD","details":"The command line remained at “LINE Specify next point.”"},{"start_s":965.017,"end_s":975.129,"action":"Confirmed the line input, placed another point, and continued positioning the next segment before cancelling or changing the active command.","intent":"Extend the line geometry in the floor plan.","app":"AutoCAD","details":"Dynamic input showed LINE prompts for the next point and later Close/Undo options."},{"start_s":975.129,"end_s":988.473,"action":"Zoomed the drawing view, then initiated the MIRROR command and selected objects for mirroring.","intent":"Prepare selected floor-plan geometry for a mirrored copy.","app":"AutoCAD","details":"The view changed from a distant plan to a closer floor-plan view; the command line showed “MIRROR Select objects.”"},{"start_s":988.473,"end_s":996.177,"action":"Defined the mirror line for the selected objects, kept the source objects, and then began a ROTATE operation on the resulting geometry.","intent":"Mirror and subsequently rotate selected drawing elements.","app":"AutoCAD","details":"The command line showed “Erase source objects? [Yes/No] <No>: N” followed by ROTATE selection."},{"start_s":996.177,"end_s":1009.249,"action":"Selected objects for rotation, specified a base point, and moved the cursor to set the rotation angle.","intent":"Rotate the copied or selected floor-plan geometry into position.","app":"AutoCAD","details":"The ROTATE command showed two objects found and prompted for the rotation angle."},{"start_s":1009.249,"end_s":1016.15,"action":"Selected objects for scaling, specified a base point, and positioned the cursor to define the scale factor.","intent":"Scale the selected drawing geometry.","app":"AutoCAD","details":"The command line showed “SCALE Specify base point” and then prompted for the scale factor."},{"start_s":1016.15,"end_s":1023.147,"action":"Activated AutoCAD, adjusted the window, and interacted with the drawing while a MOVE selection remained active; selected objects were shown in the floor plan.","intent":"Continue positioning selected drawing geometry.","app":"AutoCAD","details":"MOVE command remained at the object-selection prompt."},{"start_s":1023.147,"end_s":1031.878,"action":"Selected two objects, specified a move base point, and navigated the view with scrolling while the MOVE command awaited the displacement point.","intent":"Move the selected floor-plan objects to a new position.","app":"AutoCAD","details":"The command line showed “MOVE Specify base point or [Displacement]” and later “Specify second point”; the view was zoomed or panned."},{"start_s":1031.878,"end_s":1048.496,"action":"Navigated to a doorway area, selected two objects, and initiated SCALE; specified a base point while the selected door geometry remained highlighted.","intent":"Scale the selected doorway geometry.","app":"AutoCAD","details":"The command line showed SCALE with two objects found and a base-point prompt."},{"start_s":1048.496,"end_s":1057.99,"action":"Specified the scale base point, adjusted the view, and left the SCALE operation awaiting a scale factor or reference; then pressed Escape and began entering LINE.","intent":"Finish or cancel the scale operation and start drawing a line.","app":"AutoCAD","details":"The drawing view remained focused on the doorway; the final state showed LINE awaiting its first point."},{"start_s":1057.99,"end_s":1067.858,"action":"Confirmed the prior prompt, activated LINE, and navigated around the doorway while the command awaited the first point; pressed Escape and re-entered LINE near the end.","intent":"Prepare to draw linework near the doorway.","app":"AutoCAD","details":"LINE remained active with “Specify first point” visible; no completed segment is evidenced."},{"start_s":1067.858,"end_s":1077.741,"action":"Continued positioning the cursor and view around the doorway with LINE active, then clicked to begin a line and moved the cursor to define its next point.","intent":"Draw a line segment near the doorway.","app":"AutoCAD","details":"The command line showed “LINE Specify first point” followed by “Specify next point or [Undo]”; the second point was still being positioned."},{"start_s":1077.741,"end_s":1088.596,"action":"Adjusted the AutoCAD window and view, canceled an active prompt, and zoomed out to show the full floor plan.","intent":"Reframe the drawing and exit the current command state.","app":"AutoCAD","details":"The command line ended with an erase operation reporting one object found."},{"start_s":1088.596,"end_s":1102.591,"action":"Saved the AutoCAD drawing, then adjusted the window and view around the floor plan.","intent":"Preserve the drawing and reposition the workspace for continued editing.","app":"AutoCAD","details":null},{"start_s":1102.591,"end_s":1110.589,"action":"Entered a command input, zoomed the floor plan, canceled the preceding prompt, and initiated OFFSET with the distance field active.","intent":"Begin offsetting a selected drawing element.","app":"AutoCAD","details":"The command line showed OFFSET and requested an offset distance."},{"start_s":1110.589,"end_s":1122.385,"action":"Entered an offset distance of 9, selected a drawing element, and continued the OFFSET operation while panning and zooming the view.","intent":"Create an offset line at the specified distance.","app":"AutoCAD","details":"The command line requested the side point for the offset."},{"start_s":1122.385,"end_s":1127.57,"action":"Entered an additional offset distance of 0.5 inches, confirmed it, then canceled the remaining OFFSET prompt after adjusting the view.","intent":"Apply a smaller offset and end the offset sequence.","app":"AutoCAD","details":"The command history displayed an offset value of 4.5 inches before cancellation."},{"start_s":1127.57,"end_s":1138.13,"action":"Confirmed the prior command, adjusted the drawing view, canceled the OFFSET prompt, and typed L to invoke the LINE command before specifying the next point.","intent":"Start drawing a new line segment in the floor plan.","app":"AutoCAD","details":"The final view showed the LINE command active with a next-point prompt."},{"start_s":1138.13,"end_s":1151.711,"action":"Activated AutoCAD and adjusted the drawing view with window movements and scrolling. Started the LINE command, entered a first point, then canceled the unfinished line operation.","intent":"Prepare and inspect the floor-plan drawing while attempting a line.","app":"AutoCAD","details":"The view changed from a mostly empty area to a visible floor-plan section; the command line ended with the LINE operation canceled."},{"start_s":1151.711,"end_s":1162.704,"action":"Entered the R command and navigated the drawing view by dragging and scrolling. Began a trim-related operation, selected or dragged across drawing geometry, and then canceled it.","intent":"Modify or inspect floor-plan geometry using a command and view navigation.","app":"AutoCAD","details":"The command history shows prompts for selecting objects to trim or shift and ends with Cancel."},{"start_s":1162.704,"end_s":1172.545,"action":"Entered an offset distance of 91 and repeatedly clicked drawing geometry to select objects or specify offset sides. Created additional parallel lines in the floor-plan area while continuing the OFFSET command.","intent":"Offset existing floor-plan lines by the specified distance.","app":"AutoCAD","details":"The OFFSET prompt changed from specifying distance to selecting objects to offset; multiple new parallel vertical lines became visible."},{"start_s":1172.545,"end_s":1183.268,"action":"Continued selecting objects and sides for the active OFFSET command across the right side of the drawing. Added more parallel vertical lines and panned the view toward the right.","intent":"Continue applying repeated offsets to floor-plan geometry.","app":"AutoCAD","details":"The command remained at the Select object to offset prompt while the view shifted and additional parallel lines were visible."},{"start_s":1183.268,"end_s":1197.935,"action":"Continued clicking and dragging to select objects for offsetting across the drawing, then pressed Escape to stop the operation. Scrolled and adjusted the view, leaving the floor plan centered on the newly added parallel lines.","intent":"Finish the repeated offset edits and review the resulting geometry.","app":"AutoCAD","details":"The command line shows the OFFSET operation canceled after multiple selections; the final view contains a group of parallel vertical lines."},{"start_s":1197.935,"end_s":1203.859,"action":"Pressed Enter and started the LINE command, then clicked to place a first point and drew a horizontal segment. Pressed Escape to cancel the unfinished line command; a WhatsApp notification appeared over the lower-right corner.","intent":"Add a line segment in the edited floor-plan area, then stop the command.","app":"AutoCAD","details":"The command line ends with LINE canceled; a WhatsApp notification reports 39 unread messages."},{"start_s":1203.859,"end_s":1216.852,"action":"Entered and confirmed a command, resized the AutoCAD window, then panned and zoomed around the G+1 PLAN drawing; left an active trim prompt visible.","intent":"Navigate and inspect the floor-plan drawing while working in an AutoCAD editing command.","app":"AutoCAD","details":"The view changed from a small full-plan view to a close-up of the plan."},{"start_s":1216.852,"end_s":1226.757,"action":"Entered and confirmed another command, dragged across the drawing, then panned and zoomed; left the TRIM command active with an object-selection prompt.","intent":"Continue inspecting or editing geometry in the floor plan using AutoCAD navigation and trim controls.","app":"AutoCAD","details":"A highlighted rectangular object appeared briefly during the drag, and the command line showed TRIM options."},{"start_s":1226.757,"end_s":1231.792,"action":"Opened the AutoCAD application menu, selected the recent furniture (3).dwg drawing, and waited for the foreign DWG file to load.","intent":"Open the furniture reference drawing in AutoCAD.","app":"AutoCAD","details":"The title changed to furniture (3).dwg after the loading dialog."},{"start_s":1231.792,"end_s":1250.716,"action":"Reviewed the furniture (3).dwg drawing by panning and zooming across furniture and material reference layouts, then opened and dismissed a command or prompt.","intent":"Inspect the furniture reference drawing and its layout details.","app":"AutoCAD","details":"Visible content included furniture, vehicle, material, planting, and appliance illustrations with Chinese labels."},{"start_s":1250.716,"end_s":1256.684,"action":"Switched back to G+1 [hidden], panned and zoomed the floor plan, then initiated a copy-related operation and began defining a selection window.","intent":"Return to the floor plan and prepare geometry for copying or selection.","app":"AutoCAD","details":"The command line showed a copy-related message and then requested the opposite corner of a selection window."},{"start_s":1256.684,"end_s":1268.894,"action":"Returned to furniture (3).dwg, panned and zoomed across the reference layout, then started a paste-clip operation and moved the view while leaving the insertion-point prompt active.","intent":"Navigate the reference drawing and prepare to place copied geometry.","app":"AutoCAD","details":"The command line showed “_pasteclip Specify insertion point,” and the final view displayed multiple furniture reference panels."},{"start_s":1268.894,"end_s":1278.682,"action":"Switched to AutoCAD, briefly manipulated the window, and left the G+1 [hidden] drawing visible before returning to Windows Explorer.","intent":"Manage the AutoCAD window and drawing view.","app":"AutoCAD","details":"The command line showed PASTECLIP awaiting an insertion point."},{"start_s":1278.682,"end_s":1292.177,"action":"Switched to the furniture (3).dwg tab, panned or zoomed across furniture layout drawings, selected a table arrangement, and then hid AutoCAD to return to Windows Explorer.","intent":"Review and select furniture drawing content.","app":"AutoCAD","details":"The drawing displayed multiple table layouts with Chinese labels; a table arrangement was highlighted near the end."},{"start_s":1292.177,"end_s":1306.161,"action":"Returned to G+1 [hidden], adjusted the view, and initiated the COPY command to select drawing objects.","intent":"Prepare selected floor-plan objects for copying.","app":"AutoCAD","details":"The command line ended at “COPY Select objects:”."},{"start_s":1306.161,"end_s":1322.123,"action":"Continued selecting objects and used MOVE on the floor plan, repositioning the view and leaving AutoCAD prompting for a base point or displacement.","intent":"Reposition selected floor-plan elements.","app":"AutoCAD","details":"The command line showed MOVE with selected objects and a base-point prompt."},{"start_s":1322.123,"end_s":1331.35,"action":"Worked through selection and transformation commands, attempted a rotation, and then selected a single object for MOVE in the floor plan.","intent":"Transform and reposition a furniture object.","app":"AutoCAD","details":"The command line reported “Too many objects selected for INTERSECT” and later showed ROTATE followed by MOVE."},{"start_s":1331.35,"end_s":1345.142,"action":"Continued the MOVE operation on the selected furniture object, zoomed or panned to a closer floor-plan view, and left the command awaiting the second point or displacement.","intent":"Place the selected furniture object in the floor plan.","app":"AutoCAD","details":"The command line showed one object selected and a MOVE base-point/second-point prompt."},{"start_s":1345.142,"end_s":1361.952,"action":"Adjusted the AutoCAD window, selected the furniture group, and initiated rotation and movement operations; left the drawing with the furniture highlighted and a Move command active.","intent":"Reposition and modify furniture elements in the floor plan.","app":"AutoCAD","details":"G+1 [hidden] remained open."},{"start_s":1361.952,"end_s":1376.604,"action":"Selected and moved the furniture group into the floor-plan area, zoomed and panned around the drawing, then canceled the active operation.","intent":"Place the selected furniture within the plan and inspect its position.","app":"AutoCAD","details":"The furniture appears positioned near the right side of the plan before the view was zoomed in."},{"start_s":1376.604,"end_s":1389.918,"action":"Zoomed and panned to a close view of the plan, started the Line command, placed a line segment, and canceled the unfinished line operation.","intent":"Begin adding or editing linework near the plan geometry.","app":"AutoCAD","details":"The final view shows close-up wall geometry with a diagonal line segment visible."},{"start_s":1389.918,"end_s":1396.443,"action":"Started the Trim command, selected or dragged across drawing geometry to trim, and canceled the trim selection.","intent":"Trim unwanted portions of the plan linework.","app":"AutoCAD","details":"The command line shows TRIM and a canceled fence-style selection."},{"start_s":1396.443,"end_s":1406.221,"action":"Returned to the Line command, attempted to specify a first point and line direction, then canceled the unfinished line.","intent":"Create additional linework in the close-up plan area.","app":"AutoCAD","details":"No completed new line is confirmed in the final view."},{"start_s":1406.221,"end_s":1415.551,"action":"Started another Line command, clicked and dragged to define linework, then canceled after specifying the next point.","intent":"Continue drawing or adjusting line geometry near the plan boundary.","app":"AutoCAD","details":"The final view shows the existing wall geometry and a diagonal segment; the line command is canceled."},{"start_s":1415.551,"end_s":1431.025,"action":"Activated the TRIM command, clicked and dragged around the floor-plan geometry, and panned or zoomed the drawing while leaving TRIM active.","intent":"Trim or inspect selected floor-plan linework.","app":"AutoCAD","details":"Command line displayed TRIM and prompted to select objects."},{"start_s":1431.025,"end_s":1439.636,"action":"Confirmed the active command, started LINE, placed several points near the doorway area, and canceled the line operation.","intent":"Add or adjust linework near the doorway.","app":"AutoCAD","details":"LINE prompted for the first point, then for the next point before cancellation."},{"start_s":1439.636,"end_s":1451.961,"action":"Reactivated TRIM, clicked multiple segments around the doorway and adjacent wall geometry, and canceled the command.","intent":"Trim intersecting or unwanted wall segments.","app":"AutoCAD","details":"TRIM remained active while the drawing view stayed focused on the doorway."},{"start_s":1451.961,"end_s":1462.025,"action":"Started LINE, selected a first point near the wall corner, and moved the cursor to specify the next point with dynamic input.","intent":"Draw a line segment from the wall corner.","app":"AutoCAD","details":"Dynamic input showed distance and angle fields while LINE awaited the next point."},{"start_s":1462.025,"end_s":1472.58,"action":"Continued positioning and clicking points for the LINE command, then canceled the unfinished line.","intent":"Construct and then abandon a line segment near the doorway.","app":"AutoCAD","details":"LINE prompted for subsequent points and ended with a cancellation."},{"start_s":1472.58,"end_s":1483.163,"action":"Reactivated TRIM, clicked and dragged around the wall and doorway geometry, panned or zoomed to a wider view, and canceled the command.","intent":"Trim or review floor-plan geometry around the doorway.","app":"AutoCAD","details":"The final view showed a wider portion of the plan, with TRIM canceled."},{"start_s":1483.163,"end_s":1497.675,"action":"Activated AutoCAD, adjusted the drawing view with zoom/pan gestures, and worked through an active LINE command before erasing one found object.","intent":"Modify and inspect the floor plan geometry.","app":"AutoCAD","details":"The view changed from a close-up wall area to a broader furnished floor-plan view; the command line reported “_.erase 1 found.”"},{"start_s":1497.675,"end_s":1505.752,"action":"Continued the LINE command by selecting points around the floor plan, then canceled the unfinished line and panned/zoomed to another area.","intent":"Attempt and then abandon a line edit in the floor plan.","app":"AutoCAD","details":"The command line ended with “*Cancel*,” leaving the drawing in a different zoomed view."},{"start_s":1505.752,"end_s":1514.619,"action":"Entered the R command, dragged across the drawing to select or edit geometry, canceled the operation, and panned/zoomed around the plan.","intent":"Perform a geometry modification or selection in the floor plan.","app":"AutoCAD","details":"The command prompt showed selection/edit instructions and ended with “*Cancel*.”"},{"start_s":1514.619,"end_s":1529.985,"action":"Saved the drawing, navigated to the bedroom area, opened the Text menu, and started a single-line text command with height set to 8.","intent":"Add a room label to the floor plan.","app":"AutoCAD","details":"The Text menu displayed Multiline Text and Single Line; the command line showed TEXT and a height value of 8."},{"start_s":1529.985,"end_s":1539.593,"action":"Completed the text setup by confirming the height and rotation, then entered “GUEST ROOM” as the text content.","intent":"Create the guest-room label in the bedroom area.","app":"AutoCAD","details":"AutoCAD displayed the text-formatting interface and then accepted the room-name entry."},{"start_s":1539.593,"end_s":1551.741,"action":"Entered the second text line “10'X 11'6\",” confirmed the text, and left the GUEST ROOM label with its dimensions visible on the plan while initiating a copy selection.","intent":"Finish and position the guest-room annotation.","app":"AutoCAD","details":"The visible label reads “GUEST ROOM” and “10'X 11'6\"”; the command line later showed COPY and “Select objects.”"},{"start_s":1551.741,"end_s":1561.65,"action":"Switched to AutoCAD and continued the active COPY command, panning and zooming across the floor plan while specifying successive displacement points for duplicated guest-room elements.","intent":"Continue copying and positioning floor-plan elements.","app":"AutoCAD","details":"The command line remained at COPY with prompts for base and second points."},{"start_s":1561.65,"end_s":1571.617,"action":"Continued the COPY operation, panning across the drawing and placing additional guest-room copies around the plan.","intent":"Populate the floor plan with repeated guest-room elements.","app":"AutoCAD","details":"Multiple guest-room labels and furnishings were visible while the COPY prompt requested second points."},{"start_s":1571.617,"end_s":1581.494,"action":"Panned and zoomed through the plan, then continued selecting displacement points for the active COPY command across several guest rooms.","intent":"Position additional copied floor-plan elements.","app":"AutoCAD","details":"The drawing view expanded to show several labeled guest rooms and furnishings."},{"start_s":1581.494,"end_s":1591.805,"action":"Continued navigating the floor plan and specifying second points for the active COPY command, moving across multiple guest-room labels and room boundaries.","intent":"Continue arranging repeated plan elements.","app":"AutoCAD","details":"The command line repeatedly displayed the second-point prompt."},{"start_s":1591.805,"end_s":1604.864,"action":"Navigated and zoomed around the drawing, then pressed Escape to cancel the active COPY command and entered text-edit interaction on a guest-room label.","intent":"Finish the copy sequence and begin editing room text.","app":"AutoCAD","details":"The COPY prompt ended with Cancel, and the Text Formatting application state appeared at the boundary."},{"start_s":1604.864,"end_s":1614.398,"action":"Returned to AutoCAD, opened text editing for a guest-room label, and typed replacement text beginning with “OPEN T” into the selected label.","intent":"Rename the selected room label.","app":"AutoCAD","details":"The selected “GUEST ROOM” text changed visibly to “OPEN T” during TEXTEDIT."},{"start_s":1614.398,"end_s":1628.286,"action":"Edited the selected AutoCAD room annotation and entered the dimensions “7'2\" X 5'10\"”, then confirmed the text.","intent":"Update the Open to Sky room label with its dimensions.","app":"AutoCAD","details":"The annotation displays OPEN TO SKY with 7'2\" X 5'10\"."},{"start_s":1628.286,"end_s":1637.384,"action":"Selected another room annotation and replaced its label with “WASH AREA”, then confirmed the edit.","intent":"Rename the room annotation.","app":"AutoCAD","details":"The annotation displays WASH AREA."},{"start_s":1637.384,"end_s":1649.567,"action":"Edited the WASH AREA annotation dimensions and entered “5' X 11'6\"”, then confirmed the text and adjusted the view.","intent":"Update the Wash Area room dimensions.","app":"AutoCAD","details":"The annotation displays WASH AREA with 5' X 11'6\"."},{"start_s":1649.567,"end_s":1657.102,"action":"Selected a room annotation and replaced its label with “C TOILET”, then confirmed the edit.","intent":"Rename the room annotation.","app":"AutoCAD","details":"The annotation displays C TOILET."},{"start_s":1657.102,"end_s":1670.252,"action":"Edited the C TOILET annotation dimensions and entered “9'6\" X 5'”, then navigated the drawing view.","intent":"Update the C Toilet room dimensions.","app":"AutoCAD","details":"The annotation displays C TOILET with 9'6\" X 5'."},{"start_s":1670.252,"end_s":1677.844,"action":"Selected a room annotation and replaced its label with “DINING”, then confirmed the edit.","intent":"Rename the room annotation.","app":"AutoCAD","details":"The annotation displays DINING."},{"start_s":1677.844,"end_s":1690.353,"action":"Switched to AutoCAD and edited the dining-room dimension annotation, entering “12' X 10'4\"” and confirming it; adjusted the view and continued selecting annotation text.","intent":"Update the dining-room label dimensions.","app":"AutoCAD","details":"The DINING label displays 12' X 10'4\"."},{"start_s":1690.353,"end_s":1697.297,"action":"Selected an annotation and entered “KITCHEN,” confirming the text; resized and repositioned the AutoCAD view while the kitchen label updated.","intent":"Rename the selected room annotation to KITCHEN.","app":"AutoCAD","details":"The drawing shows KITCHEN with the existing dimension text 10' X 11'6\"."},{"start_s":1697.297,"end_s":1710.561,"action":"Selected the kitchen dimension text and entered “12' X 10'4\",” confirming the edit; adjusted the view afterward.","intent":"Correct the kitchen-room dimensions.","app":"AutoCAD","details":"The KITCHEN annotation displays 12' X 10'4\"."},{"start_s":1710.561,"end_s":1716.884,"action":"Selected a room annotation and entered “LIVING,” confirming the text while navigating to the living-room area.","intent":"Rename the selected room annotation to LIVING.","app":"AutoCAD","details":"The LIVING label appears beside the living-room furniture and retains its dimension line."},{"start_s":1716.884,"end_s":1730.621,"action":"Edited the living-room dimensions by entering “12'10\" X 19'” and confirming; zoomed or panned out to review the surrounding floor plan.","intent":"Update the living-room dimensions.","app":"AutoCAD","details":"The LIVING annotation displays 12'10\" X 19'."},{"start_s":1730.621,"end_s":1736.53,"action":"Selected a room annotation and entered “LAWN,” confirming the label; adjusted the view to show the lawn area.","intent":"Rename the selected area annotation to LAWN.","app":"AutoCAD","details":"The LAWN label appears with dimensions 10' X 11'6\"."},{"start_s":1736.53,"end_s":1753.218,"action":"Selected the LAWN annotation and replaced its dimensions with 13'6\" X 9', then adjusted the view while AutoCAD remained in text-edit selection mode.","intent":"Update the lawn dimensions in the floor-plan annotation.","app":"AutoCAD","details":"The LAWN label visibly changed from 10' X 11'6\" to 13'6\" X 9'."},{"start_s":1753.218,"end_s":1759.452,"action":"Entered VERANDAH in the active text annotation and confirmed it, leaving the label displayed above its dimensions.","intent":"Rename the selected room or area annotation.","app":"AutoCAD","details":"The annotation visibly reads VERANDAH with dimensions 10' X 11'6\"."},{"start_s":1759.452,"end_s":1772.24,"action":"Selected the VERANDAH dimensions and changed them to 4' X 4'8\", then zoomed or panned out and saved the drawing before switching to Windows Explorer.","intent":"Correct the verandah dimensions and save the updated floor plan.","app":"AutoCAD","details":"The final AutoCAD view shows VERANDAH 4' X 4'8\"."},{"start_s":1772.24,"end_s":1782.712,"action":"Returned to AutoCAD, edited the selected room label from GUEST ROOM to OPEN AREA, and confirmed the text.","intent":"Rename the selected room annotation.","app":"AutoCAD","details":"The label visibly changed to OPEN AREA while its dimensions remained 10' X 11'6\"."},{"start_s":1782.712,"end_s":1796.66,"action":"Edited the OPEN AREA dimensions, entering 7'8\" X 13'8\", and adjusted the view to show the updated annotation in the floor plan.","intent":"Update the open-area dimensions.","app":"AutoCAD","details":"The final view shows OPEN AREA 7'8\" X 13'8\"."},{"start_s":1796.66,"end_s":1806.119,"action":"Selected the GUEST ROOM annotation and replaced its label with ENTRANCE, then left the text-edit selection active.","intent":"Rename the selected floor-plan annotation.","app":"AutoCAD","details":"The visible label is partially clipped as ENTRAN... during editing, with dimensions 10' X 11'6\"."},{"start_s":1806.119,"end_s":1816.096,"action":"Edited a room annotation, entered “ROAD,” confirmed it, and panned or zoomed the drawing while leaving AutoCAD in annotation-selection mode.","intent":"Rename the selected room label to ROAD and reposition the drawing view.","app":"AutoCAD","details":"The ROAD label appears above the existing 10'X 11'6\" dimension."},{"start_s":1816.096,"end_s":1826.895,"action":"Selected and erased one annotation object, then navigated the drawing and selected another room annotation.","intent":"Modify room labels in the floor-plan drawing.","app":"AutoCAD","details":"The view shows ROAD and GUEST ROOM labels; the command line reports “_erase 1 found.”"},{"start_s":1826.895,"end_s":1839.958,"action":"Edited the selected annotation and entered “GROUND FLOOR PLAN,” then confirmed the text and adjusted the view.","intent":"Replace the selected room label with GROUND FLOOR PLAN.","app":"AutoCAD","details":"The new label is visible above the 10'X 11'6\" dimension, with the text still selected or being edited."},{"start_s":1839.958,"end_s":1854.646,"action":"Selected annotation text, zoomed or panned from a close-up of GROUND FLOOR PLAN to a broader floor-plan view, and initiated another command.","intent":"Review the updated plan and navigate to another area of the drawing.","app":"AutoCAD","details":"The floor plan becomes visible with rooms including GUEST ROOM, C TOILET, OPEN TO SKY, WASH AREA, KITCHEN, DINING, and LIVING."},{"start_s":1854.646,"end_s":1861.944,"action":"Entered and confirmed a drawing command, navigated to the upper floor-plan area, started a LINE operation, and then canceled it.","intent":"Begin and abandon a line-drawing operation near the toilet and wash-area geometry.","app":"AutoCAD","details":"The command line shows LINE prompts followed by cancellation; no completed line is evident."},{"start_s":1861.944,"end_s":1867.253,"action":"Entered TRIM, dragged across the drawing, selected or attempted to trim geometry, and canceled the command.","intent":"Trim unwanted or intersecting floor-plan linework.","app":"AutoCAD","details":"The command line shows TRIM prompts and ends with “*Cancel*”; the view is centered on the C TOILET area."},{"start_s":1867.253,"end_s":1878.793,"action":"Started the LINE command, entered a length of 2'-4\", and canceled after positioning the next point.","intent":"Draw a short horizontal line in the floor plan.","app":"AutoCAD","details":"The command line ended at the default command prompt after cancellation."},{"start_s":1878.793,"end_s":1886.622,"action":"Started another LINE command, placed a first point, and continued specifying the next point with an orthogonal preview before entering T.","intent":"Create another line segment in the floor plan.","app":"AutoCAD","details":"The LINE command remained active while the next point was being specified."},{"start_s":1886.622,"end_s":1894.532,"action":"Entered R and confirmed it, viewed a zoomed area containing the C TOILET and WASH labels, then canceled the active command and began entering 2.","intent":"Navigate or modify the drawing around the labeled rooms.","app":"AutoCAD","details":"The visible command history showed a canceled stretch-related operation."},{"start_s":1894.532,"end_s":1903.782,"action":"Started OFFSET, selected or attempted to select drawing geometry, and entered a distance of 2 while leaving the command at the side-selection prompt.","intent":"Create a parallel offset line in the floor plan.","app":"AutoCAD","details":"The OFFSET command was still active and prompting for the side to offset."},{"start_s":1903.782,"end_s":1908.487,"action":"Entered a distance of 1 for OFFSET and selected the side of the geometry, producing an additional parallel line while keeping OFFSET active.","intent":"Add another parallel line at a one-unit offset.","app":"AutoCAD","details":"The command prompt continued to request an object or further offset operation."},{"start_s":1908.487,"end_s":1915.642,"action":"Panned and zoomed the drawing with middle-button navigation and scrolls, bringing the C TOILET and WASH AREA labels and surrounding doors into view.","intent":"Review the adjusted floor-plan area.","app":"AutoCAD","details":"No new geometry command was completed during the navigation."},{"start_s":1915.642,"end_s":1924.342,"action":"Scrolled and middle-clicked several times while viewing the floor plan around the guest room, toilet, wash area, dining area, and stairs.","intent":"Navigate and inspect the drawing.","app":"Autodesk AutoCAD","details":"No visible geometry change was confirmed."},{"start_s":1924.342,"end_s":1936.54,"action":"Scrolled to the verandah, living, open area, and lawn portion of the plan, then interacted with the AutoCAD window and entered a numeric value.","intent":"Navigate the plan and adjust the active AutoCAD interaction.","app":"Autodesk AutoCAD","details":"The drawing remained visible while the application window was resized or moved."},{"start_s":1936.54,"end_s":1952.774,"action":"Completed the pending input, moved and resized the AutoCAD window, then initiated OFFSET and attempted to select an object; canceled the command and typed L.","intent":"Modify or inspect linework near the verandah and open area.","app":"Autodesk AutoCAD","details":"The command line showed OFFSET prompts, but no completed offset was confirmed."},{"start_s":1952.774,"end_s":1958.321,"action":"Completed the pending command input, resized the AutoCAD window, and started the LINE command; selected a first point and moved toward the next point.","intent":"Draw linework in the verandah/open-area region.","app":"Autodesk AutoCAD","details":"LINE remained active with a prompt to specify the next point."},{"start_s":1958.321,"end_s":1962.861,"action":"Entered and confirmed command input, clicked in the drawing, canceled the active line operation, and typed T.","intent":"Continue editing the floor-plan geometry.","app":"Autodesk AutoCAD","details":"The line command was canceled; no completed new line was confirmed."},{"start_s":1962.861,"end_s":1977.161,"action":"Entered and confirmed a command, dragged across the drawing, clicked near the verandah, and canceled the active operation; the view shifted and TRIM was then active before another command input began.","intent":"Trim or adjust geometry around the verandah and adjacent walls.","app":"Autodesk AutoCAD","details":"The final view showed the verandah enlarged, with TRIM prompts followed by an OFFSET distance prompt."},{"start_s":1977.161,"end_s":1988.343,"action":"Entered an offset distance and continued selecting an offset side around the verandah geometry, then canceled the active command.","intent":"Modify the verandah outline with the OFFSET command.","app":"AutoCAD","details":"The drawing remained focused on the verandah labeled 4' X 4'8\"."},{"start_s":1988.343,"end_s":2003.878,"action":"Canceled the prior command, navigated the drawing view, and started the RECTANG command before positioning the first corner near the entrance and lawn area.","intent":"Create a rectangular element in the lower plan area.","app":"AutoCAD","details":"The view changed to show the kitchen, living room, verandah, open area, lawn, and entrance."},{"start_s":2003.878,"end_s":2014.61,"action":"Started RECTANG, dragged across the lower plan area, then used trimming and copying interactions on the verandah and open-area geometry; left COPY active awaiting object selection.","intent":"Edit and duplicate plan geometry near the verandah and entrance.","app":"AutoCAD","details":"Visible prompts included trim selection and COPY object selection."},{"start_s":2014.61,"end_s":2024.626,"action":"Selected the rectangular geometry, specified a copy base point, and positioned a second copy toward the open-area and entrance region.","intent":"Duplicate the selected rectangular element within the floor plan.","app":"AutoCAD","details":"COPY remained active with a prompt for another second point or exit."},{"start_s":2024.626,"end_s":2033.722,"action":"Continued positioning the copied rectangle, canceled the repeated copy operation, and scrolled the drawing view while reviewing the resulting geometry.","intent":"Finish the rectangle duplication and inspect its placement.","app":"AutoCAD","details":"The plan showed the verandah, open area, lawn, and entrance with the copied rectangle highlighted."},{"start_s":2033.722,"end_s":2046.218,"action":"Canceled the active copy prompt, selected the rectangular element, zoomed or panned out to review the broader floor plan, and issued the save command.","intent":"Review the edited drawing and save changes.","app":"AutoCAD","details":"The final view showed the upper plan with guest room, dining, kitchen, open-to-sky area, wash area, and C toilet."},{"start_s":2046.218,"end_s":2052.725,"action":"Activated AutoCAD, adjusted the window and view, started the LINE command, then canceled it without placing a line.","intent":"Attempt to draw a line in the floor plan.","app":"AutoCAD","details":"The drawing shows the open-to-sky area and adjacent geometry."},{"start_s":2052.725,"end_s":2058.565,"action":"Selected drawing geometry and used JOIN, leaving the command active while selecting additional objects.","intent":"Join adjacent line segments into combined geometry.","app":"AutoCAD","details":"The command line reports one source object and two total objects found."},{"start_s":2058.565,"end_s":2070.226,"action":"Started LINE again, moved around the drawing while adjusting the view, canceled the command, and began another LINE entry.","intent":"Attempt to create or inspect linework in the plan.","app":"AutoCAD","details":"No completed new line is visibly confirmed."},{"start_s":2070.226,"end_s":2083.112,"action":"Continued the LINE command while panning or zooming around the drawing, then canceled it and began entering the TRIM command.","intent":"Switch from line creation to trimming existing geometry.","app":"AutoCAD","details":"The AutoCAD drawing view was repositioned and the application was briefly hidden before the next command."},{"start_s":2083.112,"end_s":2097.113,"action":"Started TRIM, navigated and zoomed around the plan, selected or dragged across geometry, then canceled the trim operation and began another TRIM entry.","intent":"Trim or clean up intersecting plan lines.","app":"AutoCAD","details":"The command line shows trim prompts and a canceled cutting-edge selection."},{"start_s":2097.113,"end_s":2106.444,"action":"Started TRIM, dragged across and inspected the floor plan, zoomed out to show the guest room, C toilet, wash area, and open-to-sky area, then canceled the operation.","intent":"Continue cleaning up wall or boundary geometry in the floor plan.","app":"AutoCAD","details":"The final view shows the labeled room layout with the trim command canceled."},{"start_s":2106.444,"end_s":2119.497,"action":"Activated AutoCAD, navigated around the floor plan, and used the command line to cancel and save while changing the view from the upper rooms to the lower living and entrance areas.","intent":"Review and navigate the floor-plan drawing.","app":"AutoCAD","details":"The drawing remained open and visible; the view shifted to show the dining, kitchen, living, verandah, lawn, open area, entrance, and road."},{"start_s":2119.497,"end_s":2123.567,"action":"Started the LINE command and positioned the cursor in the lawn area, entering a distance value while AutoCAD continued prompting for the next point.","intent":"Begin drawing a line in the lower portion of the floor plan.","app":"AutoCAD","details":"The command line showed LINE and prompts for the first and next points; completion was not visible."},{"start_s":2123.567,"end_s":2132.532,"action":"Continued attempting the LINE command with cursor positioning and clicks around the lawn and living-area boundary, then canceled and reinitiated the command.","intent":"Adjust or restart line placement in the floor plan.","app":"AutoCAD","details":"AutoCAD repeatedly displayed the “Specify first point” prompt, with no confirmed completed line visible."},{"start_s":2132.532,"end_s":2142.528,"action":"Entered a command and zoomed or navigated around the lower floor plan, then used TRIM and clicked near the lawn and verandah boundary while AutoCAD prompted for objects to trim.","intent":"Modify drawing geometry near the lower exterior areas.","app":"AutoCAD","details":"The TRIM prompt was visible and the command was eventually canceled; no definite trim result was shown."},{"start_s":2142.528,"end_s":2155.999,"action":"Canceled the active operation, zoomed out to review the complete ground-floor plan, then initiated SCALE and selected drawing objects.","intent":"Review the full plan and begin scaling selected geometry.","app":"AutoCAD","details":"The full plan became visible, and the command line showed SCALE with one object found during selection."},{"start_s":2155.999,"end_s":2162.736,"action":"Continued the SCALE command, selected additional objects around the verandah and lower plan, and left AutoCAD prompting for the scale factor or reference.","intent":"Prepare to scale selected floor-plan elements.","app":"AutoCAD","details":"The command line showed SCALE, with two objects found and the scale-factor prompt still active."},{"start_s":2162.736,"end_s":2172.922,"action":"Activated AutoCAD, adjusted the drawing view, and worked through an active SCALE command before cancelling it. Saved the drawing and interacted with the command area while the floor plan remained visible.","intent":"Adjust and review the floor-plan drawing, then save the current state.","app":"AutoCAD","details":"The command line shows SCALE followed by cancellation; a WhatsApp notification briefly appeared."},{"start_s":2172.922,"end_s":2178.696,"action":"Reactivated AutoCAD and continued a MOVE operation on selected floor-plan objects, positioning the verandah-related geometry with the cursor and dynamic input.","intent":"Move selected drawing elements within the floor plan.","app":"AutoCAD","details":"The command line shows MOVE with two objects found and prompts for the second point."},{"start_s":2178.696,"end_s":2194.209,"action":"Completed the MOVE interaction and zoomed out to review the full house plan, then initiated another MOVE operation while navigating the drawing view.","intent":"Reposition selected plan elements and inspect the overall layout.","app":"AutoCAD","details":"The full floor plan becomes visible; the command line ends in a MOVE object-selection prompt."},{"start_s":2194.209,"end_s":2204.87,"action":"Worked in a zoomed view of the guest room, toilet, dining, and stair area, then zoomed out and initiated a SCALE operation on selected objects.","intent":"Adjust the scale or size of selected floor-plan elements.","app":"AutoCAD","details":"The command line shows MOVE followed by SCALE Select objects."},{"start_s":2204.87,"end_s":2211.912,"action":"Zoomed and panned around the upper and middle portions of the floor plan, saved the drawing, and left the SCALE command awaiting a scale factor or copy/reference choice.","intent":"Review the plan and save while preparing a scale adjustment.","app":"AutoCAD","details":"The command line shows SCALE prompts and later _qsave."},{"start_s":2211.912,"end_s":2222.156,"action":"Entered a LINE command, specified a first point near the stair and dining area, and moved the cursor to preview the next segment with dynamic distance and angle feedback.","intent":"Draw a line segment in the stair and dining area of the floor plan.","app":"AutoCAD","details":"The LINE command remains active at the end, prompting for the next point; the final Escape-related event does not show completion."},{"start_s":2222.156,"end_s":2234.182,"action":"Adjusted the AutoCAD window repeatedly and continued the MLEADER command, leaving the drawing active at the leader-arrowhead placement prompt.","intent":"Continue placing a leader annotation in the floor plan.","app":"AutoCAD","details":"Drawing view remained on the floor plan near the labeled toilet area."},{"start_s":2234.182,"end_s":2239.334,"action":"Switched back to the drawing, canceled the active leader prompt, and initiated MOVE while selecting objects.","intent":"Transition from leader placement to moving drawing content.","app":"AutoCAD","details":"Command line showed MOVE with a Select objects prompt."},{"start_s":2239.334,"end_s":2248.627,"action":"Selected an object for MOVE, specified a base point, and began specifying the second point; canceled or left the command active while adjusting the window.","intent":"Move a selected annotation or drawing object.","app":"AutoCAD","details":"The selected leader-like annotation was visibly displaced toward the right."},{"start_s":2248.627,"end_s":2266.62,"action":"Navigated the drawing and used COPY, selecting the C TOILET annotation area and continuing the multiple-copy placement workflow.","intent":"Duplicate the toilet annotation within the floor plan.","app":"AutoCAD","details":"The view changed to show the C TOILET label and its 9'6\" X 5' dimensions; COPY remained active."},{"start_s":2266.62,"end_s":2274.417,"action":"Specified a copy base point and second point, placing another C TOILET annotation lower in the plan while keeping COPY in multiple mode.","intent":"Create an additional copy of the toilet label.","app":"AutoCAD","details":"A second C TOILET label appeared below the original near the guest room and wash area."},{"start_s":2274.417,"end_s":2280.278,"action":"Entered UP, completed text editing, and moved the resulting UP annotation to a new position below the rooms.","intent":"Add or reposition an upward-direction annotation.","app":"AutoCAD","details":"The floor plan showed an UP label below the guest room and C TOILET."},{"start_s":2280.278,"end_s":2289.092,"action":"Switched to AutoCAD, resized the drawing window repeatedly, navigated the floor plan with middle-button view controls, and zoomed in on the plan.","intent":"Adjust the drawing view before editing dimensions.","app":"AutoCAD","details":"Displayed G+1 [hidden] and zoomed from the full plan toward the upper rooms."},{"start_s":2289.092,"end_s":2302.081,"action":"Opened the Dimension Style Manager, selected ISO-25, and opened its modification dialog. Reviewed the Primary Units settings, including the unit-format dropdown.","intent":"Inspect and begin modifying the ISO-25 dimension style.","app":"AutoCAD","details":"The Modify Dimension Style: ISO-25 dialog was visible with Decimal selected and the unit-format list expanded."},{"start_s":2302.081,"end_s":2312.03,"action":"Returned to the ISO-25 dimension-style dialog, switched to the Text tab, and edited the text-height field to 4.5 before confirming the change.","intent":"Set the ISO-25 dimension text height.","app":"AutoCAD","details":"The Text tab showed text height 2.5 before the typed replacement."},{"start_s":2312.03,"end_s":2320.152,"action":"Closed the dimension-style dialogs, started the DIMLINEAR command, selected the first extension point along the top of the plan, and placed a horizontal dimension reading 26'-6\".","intent":"Add a linear dimension to the floor plan.","app":"AutoCAD","details":"The new dimension was visible above the upper boundary of the plan."},{"start_s":2320.152,"end_s":2328.789,"action":"Continued DIMLINEAR, selected another first extension point near the upper-right plan boundary, and panned or zoomed down toward the lower rooms while the command awaited the second point.","intent":"Create another linear dimension on the plan.","app":"AutoCAD","details":"The command prompt requested the first extension line origin and the view shifted to the dining, kitchen, living, lawn, and open-area portion."},{"start_s":2328.789,"end_s":2346.282,"action":"Navigated and zoomed around the lower floor plan, selected extension points for DIMLINEAR, and produced a vertical dimension reading 34'-5.8\"; then canceled the active command and opened Text Formatting.","intent":"Add and review a lower-plan dimension.","app":"AutoCAD","details":"The final view showed the vertical 34'-5.8\" dimension beside the dining area, with Text Formatting opening at the end."},{"start_s":2346.282,"end_s":2355.643,"action":"Switched to AutoCAD, edited text to display “32,” confirmed the entry, and resized the window while exiting the text-edit state.","intent":"Update a visible annotation in the floor plan.","app":"AutoCAD","details":"Displayed text reads 32 near the dining area."},{"start_s":2355.643,"end_s":2366.458,"action":"Scrolled and reviewed the ground-floor plan, canceled the active command, and zoomed out to show the full plan before switching away.","intent":"Inspect the overall floor-plan layout.","app":"AutoCAD","details":"The plan shows guest room, dining, kitchen, living, lawn, open area, and road labels."},{"start_s":2366.458,"end_s":2377.207,"action":"Returned to AutoCAD, switched from the floor-plan drawing to furniture (3).dwg, and zoomed and panned across the furniture-symbol library.","intent":"Review available furniture and drafting symbols.","app":"AutoCAD","details":"The furniture drawing displays grouped furniture and landscape symbols."},{"start_s":2377.207,"end_s":2394.735,"action":"Continued panning and zooming through furniture and landscaping symbols, selected or inspected a plant group, then copied objects to the clipboard before switching away.","intent":"Prepare reusable furniture or landscape objects for insertion.","app":"AutoCAD","details":"The view ends on plant and landscaping symbols with a copy command reporting 445 found."},{"start_s":2394.735,"end_s":2405.159,"action":"Returned to the floor-plan drawing, zoomed into the open-area and entrance region, and initiated Pasteclip; left the command active at the insertion-point prompt before switching away.","intent":"Insert copied landscaping content into the floor plan.","app":"AutoCAD","details":"The command line shows PASTECLIP Specify insertion point, with the cursor positioned over the open area."},{"start_s":2405.159,"end_s":2417.62,"action":"Switched back to furniture (3).dwg, zoomed and panned across the plant symbols, then dragged a selection window around a group of landscaping objects.","intent":"Select additional landscaping objects for reuse.","app":"AutoCAD","details":"A blue crossing-selection window encloses several plant symbols."},{"start_s":2417.62,"end_s":2423.198,"action":"Switched back to AutoCAD, restored the drawing window, and interacted with the active PASTECLIP insertion prompt near the lawn area of the ground-floor plan.","intent":"Continue placing pasted drawing content in the floor plan.","app":"AutoCAD","details":"The drawing remained in an active paste insertion-point state."},{"start_s":2423.198,"end_s":2431.093,"action":"Exited the paste prompt, zoomed out to view the full ground-floor plan, and initiated the SCALE command with the plan selected.","intent":"Prepare the ground-floor plan for resizing.","app":"AutoCAD","details":"The command line shows _qsave followed by SCALE and one found object selected."},{"start_s":2431.093,"end_s":2442.788,"action":"Specified a base point for the SCALE command, then entered a scale-factor prompt while panning or zooming the drawing view.","intent":"Resize the selected floor-plan object.","app":"AutoCAD","details":"The plan became smaller in view and the command line requested a scale factor."},{"start_s":2442.788,"end_s":2448.321,"action":"Entered numeric and dimension-style text into the active dynamic input, then began the RECTANG command and positioned a large rectangle preview to the right of the plan.","intent":"Create a rectangular boundary or reference area in the drawing.","app":"AutoCAD","details":"The command line shows RECTANG awaiting the opposite corner."},{"start_s":2448.321,"end_s":2454.385,"action":"Continued entering rectangle dimensions and confirmed the input while the rectangle preview remained active beside the floor plan.","intent":"Define the rectangle's opposite corner and dimensions.","app":"AutoCAD","details":"The dynamic input shows rectangle corner coordinates and an active opposite-corner prompt."},{"start_s":2454.385,"end_s":2463.055,"action":"Zoomed and panned around the drawing, completed the rectangle, and began a MOVE operation with an object selected.","intent":"Adjust the newly created rectangle or related drawing geometry.","app":"AutoCAD","details":"The final view shows the small floor plan and a blue rectangular selection; MOVE is awaiting object selection."},{"start_s":2463.055,"end_s":2467.888,"action":"Switched to AutoCAD, adjusted the window, and interacted with the drawing while an offset operation remained active; briefly switched through Explorer and the recorder, then returned to AutoCAD and entered 9.","intent":"Continue an offset operation in the floor-plan drawing.","app":"AutoCAD","details":"The drawing shows a ground-floor plan and an active offset prompt."},{"start_s":2467.888,"end_s":2472.479,"action":"Confirmed the offset distance input, adjusted the view, and clicked in the drawing to continue selecting an object to offset.","intent":"Apply the entered offset distance to a selected drawing object.","app":"AutoCAD","details":"The command line and dynamic prompt show OFFSET waiting for an object selection."},{"start_s":2472.479,"end_s":2485.917,"action":"Clicked the drawing and command area, leaving the OFFSET command active with the offset distance input field visible; entered 1 near the end of the span.","intent":"Continue specifying offset parameters for the floor-plan geometry.","app":"AutoCAD","details":"The view remains on the floor plan with OFFSET prompting for an offset distance or object selection."},{"start_s":2485.917,"end_s":2497.308,"action":"Entered 2 inches to set a 12-inch offset distance, zoomed and panned the drawing with middle-button interactions, and clicked to select an object for offset.","intent":"Set the required offset distance and identify geometry to offset.","app":"AutoCAD","details":"The drawing view is enlarged around rectangular plan geometry and the prompt reads Select object to offset."},{"start_s":2497.308,"end_s":2503.588,"action":"Entered .5 inches and confirmed it, then zoomed or panned and clicked near the drawing while OFFSET continued prompting for an object.","intent":"Refine the offset distance and continue the offset operation.","app":"AutoCAD","details":"The command history shows a 4.5-inch distance and an active object-selection prompt."},{"start_s":2503.588,"end_s":2511.923,"action":"Entered 10 inches and confirmed it, adjusted the view, and clicked a vertical line so it became highlighted while AutoCAD prompted for the side on which to offset.","intent":"Offset the selected vertical boundary by the specified distance.","app":"AutoCAD","details":"The final view shows the selected blue vertical line and a 12-inch dynamic input beside the offset-side prompt."},{"start_s":2511.923,"end_s":2517.029,"action":"Enter 0.5 inches for the active OFFSET distance, confirm it, and click in the drawing to create an offset line. Begin entering the next distance.","intent":"Create repeated offset geometry at specified distances.","app":"AutoCAD","details":"OFFSET remains active and prompts for an object selection."},{"start_s":2517.029,"end_s":2521.733,"action":"Confirm the next OFFSET input, click the drawing, and enter 4.5 inches as the following offset distance.","intent":"Continue creating evenly spaced offset lines.","app":"AutoCAD","details":"A horizontal line is visibly selected/created while OFFSET continues."},{"start_s":2521.733,"end_s":2532.874,"action":"Click and drag in the drawing to place the offset, then enter 7 as the next distance.","intent":"Continue the repeated offset operation with another specified spacing.","app":"AutoCAD","details":"The drawing shows additional horizontal and vertical offset lines; OFFSET remains active."},{"start_s":2532.874,"end_s":2538.199,"action":"Enter 6 inches for the OFFSET distance, confirm it, and click the drawing to place the next offset.","intent":"Add another offset line using the specified distance.","app":"AutoCAD","details":"The plan gains another parallel line and OFFSET returns to object selection."},{"start_s":2538.199,"end_s":2543.494,"action":"Enter 0.5 inches, confirm it, and click the drawing to create another offset; begin entering 6 for the next distance.","intent":"Continue adding closely spaced offset geometry.","app":"AutoCAD","details":"Multiple closely spaced vertical lines are visible, with OFFSET still active."},{"start_s":2543.494,"end_s":2550.181,"action":"Enter 10 inches, confirm it, and click the drawing to place the offset, then begin entering 12 for the next offset distance.","intent":"Continue the sequence of specified offsets in the floor-plan drawing.","app":"AutoCAD","details":"A new horizontal line is visible near the lower portion of the plan; OFFSET remains active."},{"start_s":2550.181,"end_s":2555.337,"action":"Entered an offset distance of .5 inches, canceled the active prompt, then invoked TRIM and confirmed the command.","intent":"Adjust drawing geometry using offset and trim commands.","app":"AutoCAD","details":"Displayed the G+1 [hidden] floor plan."},{"start_s":2555.337,"end_s":2565.262,"action":"Selected TRIM and dragged across the drawing while the command requested objects or fence points; continued selecting and panning within the floor plan.","intent":"Trim intersecting floor-plan geometry.","app":"AutoCAD","details":"TRIM remained active with prompts for object selection and fence points."},{"start_s":2565.262,"end_s":2579.607,"action":"Continued fence/object selection and navigation in the floor plan, canceled TRIM, then started OFFSET and entered an offset distance of 0'-4.5\".","intent":"Switch from trimming to creating a fixed-distance offset.","app":"AutoCAD","details":"The OFFSET command showed the entered distance 0'-4.5\"."},{"start_s":2579.607,"end_s":2583.836,"action":"Edited the OFFSET distance input to 5' 2\" and pressed Enter.","intent":"Set the offset distance for the active drawing operation.","app":"AutoCAD","details":"The dynamic input displayed the offset distance as 15' before confirmation."},{"start_s":2583.836,"end_s":2592.721,"action":"Selected a horizontal floor-plan line for OFFSET and positioned the cursor to specify the side, zooming and navigating around the drawing.","intent":"Create an offset copy of the selected floor-plan line.","app":"AutoCAD","details":"The selected line was highlighted and the prompt requested a point on the side to offset."},{"start_s":2592.721,"end_s":2602.861,"action":"Entered an offset distance of .5 inches and confirmed it, then selected another floor-plan object while OFFSET remained active.","intent":"Apply a half-inch offset to additional drawing geometry.","app":"AutoCAD","details":"The command line returned to the prompt to select an object to offset."},{"start_s":2602.861,"end_s":2608.286,"action":"Entered 8 feet, adjusted the AutoCAD view, and continued the active OFFSET command by selecting points and entering an offset distance of 4.","intent":"Continue offsetting geometry in the floor plan.","app":"AutoCAD","details":"The drawing remained in OFFSET mode and prompted to select an object."},{"start_s":2608.286,"end_s":2613.547,"action":"Entered a 0.5-inch offset value, adjusted the view, clicked in the drawing, and began entering the next offset distance.","intent":"Continue creating offset lines in the floor plan.","app":"AutoCAD","details":"AutoCAD continued displaying the OFFSET prompt."},{"start_s":2613.547,"end_s":2617.665,"action":"Typed and confirmed another offset value while the view zoomed in on the rectangular plan geometry.","intent":"Set the next OFFSET distance and continue the drafting operation.","app":"AutoCAD","details":"The dynamic input showed a value beginning with 14 while AutoCAD prompted for the side to offset."},{"start_s":2617.665,"end_s":2622.011,"action":"Adjusted the AutoCAD view, clicked in the drawing, and began entering a 4-inch offset value.","intent":"Continue offsetting the selected floor-plan geometry.","app":"AutoCAD","details":"The command history showed a prior 14-foot 6-inch offset and a current OFFSET prompt."},{"start_s":2622.011,"end_s":2632.911,"action":"Entered a 0.5-inch offset, adjusted and panned the view, clicked in the drawing, and began entering another 4-inch value.","intent":"Continue adding successive offsets to the plan geometry.","app":"AutoCAD","details":"The drawing remained in the OFFSET command with repeated prompts for object selection and side points."},{"start_s":2632.911,"end_s":2637.785,"action":"Entered a 2-inch offset, adjusted the view, and dragged or clicked in the drawing while continuing the OFFSET command.","intent":"Continue offsetting lines in the floor plan.","app":"AutoCAD","details":"AutoCAD remained at the prompt to select an object to offset."},{"start_s":2637.785,"end_s":2654.167,"action":"Entered an offset distance of 0.5 inches, selected several points around the floor-plan geometry, and adjusted the view while leaving the OFFSET command active before starting another command.","intent":"Continue offsetting or positioning floor-plan elements.","app":"AutoCAD","details":"The drawing showed the OFFSET prompt and a 4.5-inch value in the dynamic input history."},{"start_s":2654.167,"end_s":2662.918,"action":"Ran the TRIM command, zoomed and panned across the drawing, and selected or dragged around geometry while the prompt asked for objects to trim.","intent":"Trim unwanted portions of the floor-plan geometry.","app":"AutoCAD","details":"The view briefly showed the overall ground-floor plan and adjacent rectangular plan."},{"start_s":2662.918,"end_s":2668.894,"action":"Started the LINE command, placed a first point, dragged toward a second point, and then canceled the unfinished line operation.","intent":"Draw a line segment in the floor-plan area.","app":"AutoCAD","details":"Dynamic input displayed first-point and next-point prompts with an in-progress line preview."},{"start_s":2668.894,"end_s":2675.496,"action":"Started another command sequence, dragged and clicked around the central plan geometry, then canceled and returned to a TRIM-related prompt.","intent":"Modify and trim floor-plan linework.","app":"AutoCAD","details":"The command history showed a canceled next-point operation followed by TRIM prompts."},{"start_s":2675.496,"end_s":2683.972,"action":"Ran TRIM, navigated by panning and zooming between the ground-floor plan and adjacent rectangular geometry, and selected or dragged across candidate linework for trimming.","intent":"Clean up overlapping or unwanted floor-plan lines.","app":"AutoCAD","details":"The TRIM prompt remained visible while the view shifted to show the plan more closely."},{"start_s":2683.972,"end_s":2694.057,"action":"Continued selecting and dragging within the TRIM operation, canceled the active trimming, then adjusted the view and ended with the drawing centered on both plans.","intent":"Finish or abandon the current trimming pass and review the drawing.","app":"AutoCAD","details":"The command line ended with a canceled TRIM operation; no confirmed final geometry change was visible."},{"start_s":2694.057,"end_s":2707.095,"action":"Adjusted the AutoCAD window and entered measurement and offset commands, leaving the drawing at an offset-distance prompt.","intent":"Modify and measure drawing geometry using AutoCAD command prompts.","app":"Autodesk AutoCAD","details":"The drawing remained visible while the command line progressed from MEASUREGEOM to OFFSET; an offset value was active near the end."},{"start_s":2707.095,"end_s":2712.296,"action":"Entered an offset distance of 1' 4\", then clicked drawing geometry and left OFFSET waiting for an object to offset.","intent":"Create an offset line at the specified distance.","app":"Autodesk AutoCAD","details":"The command line showed the 1' 4\" distance and the prompt to select an object to offset."},{"start_s":2712.296,"end_s":2718.481,"action":"Switched briefly through another window, returned to AutoCAD, and entered 4.5' while selecting an object and specifying the side for the offset.","intent":"Continue creating a drawing offset with a 4.5-foot distance.","app":"Autodesk AutoCAD","details":"The command remained active at the prompt to specify the point on the side to offset."},{"start_s":2718.481,"end_s":2726.825,"action":"Canceled the active offset, started TRIM, dragged across the drawing, and selected geometry for trimming before leaving the trim command active.","intent":"Trim intersecting linework in the floor-plan drawing.","app":"Autodesk AutoCAD","details":"The visible prompt changed from OFFSET to TRIM, with the drawing showing modified horizontal and vertical linework."},{"start_s":2726.825,"end_s":2732.903,"action":"Switched briefly through Windows Explorer and returned to AutoCAD, leaving an OFFSET distance prompt active with the prior value visible.","intent":"Resume offset editing of the drawing.","app":"Autodesk AutoCAD","details":"The screen showed the AutoCAD drawing and an active offset-distance input field."},{"start_s":2732.903,"end_s":2743.25,"action":"Entered 9' 10\" as the offset distance, selected drawing geometry, and continued the OFFSET operation while the view shifted to the edited linework.","intent":"Create another offset in the floor-plan drawing.","app":"Autodesk AutoCAD","details":"The command line recorded the 9' 10\" distance; the operation remained active at the end."},{"start_s":2743.25,"end_s":2757.662,"action":"Entered an offset distance and navigated the AutoCAD drawing with scrolling. Canceled the active offset prompt and resized or repositioned the application window.","intent":"Adjust and inspect drawing geometry using the Offset command.","app":"AutoCAD","details":"The drawing remained at an active offset selection prompt before the command was canceled."},{"start_s":2757.662,"end_s":2762.661,"action":"Entered an offset distance, panned the drawing with middle-button clicks, and selected a line for another offset operation.","intent":"Continue offsetting wall or line geometry in the floor plan.","app":"AutoCAD","details":"The command line showed OFFSET with a distance entry and a prompt to select an object."},{"start_s":2762.661,"end_s":2767.768,"action":"Edited the dynamic offset-distance entry to 4.5 inches and submitted it.","intent":"Set the offset distance for the active AutoCAD operation.","app":"AutoCAD","details":"The dynamic input displayed 4.5 while AutoCAD prompted for the side of the offset."},{"start_s":2767.768,"end_s":2776.743,"action":"Clicked to specify the side of the offset and continued adjusting the view. Pressed Escape while the offset prompt remained active.","intent":"Apply or preview the offset on the selected drawing line, then stop the operation.","app":"AutoCAD","details":"The drawing showed a highlighted horizontal line and the prompt to specify the point on the side to offset."},{"start_s":2776.743,"end_s":2791.121,"action":"Scrolled and panned out to review both floor-plan layouts, then repositioned the window and began another command entry.","intent":"Review the resulting plan geometry at a broader view before continuing drafting.","app":"AutoCAD","details":"The view showed the labeled ground-floor plan alongside the simpler rectangular plan."},{"start_s":2791.121,"end_s":2804.738,"action":"Entered a 0'4\" offset distance, navigated and zoomed the drawing, selected a line, and entered 10 as the next offset distance.","intent":"Create another offset line at the specified distances in the floor plan.","app":"AutoCAD","details":"AutoCAD ended with OFFSET prompting for an object selection after the 10 distance entry."},{"start_s":2804.738,"end_s":2809.727,"action":"Entered an offset distance of 0.5 inches, returned to the drawing, canceled the active OFFSET prompt, and began entering the TRIM command.","intent":"Modify drawing geometry using offset and trim operations.","app":"AutoCAD","details":"The command line showed OFFSET awaiting object selection before cancellation."},{"start_s":2809.727,"end_s":2819.183,"action":"Confirmed the TRIM command, adjusted the drawing view, and left TRIM active while the command line awaited an object to trim or extend.","intent":"Prepare to trim selected drawing geometry.","app":"AutoCAD","details":"The view and window were repeatedly repositioned and resized; no completed trim is visibly confirmed."},{"start_s":2819.183,"end_s":2838.967,"action":"Navigated and zoomed/panned around the drawing while TRIM remained active, made multiple clicks in the drawing area, then canceled the operation and opened the Measure menu.","intent":"Inspect or modify geometry and access measurement tools.","app":"AutoCAD","details":"The Measure dropdown visibly listed Quick, Distance, Radius, Angle, Area, and Volume."},{"start_s":2838.967,"end_s":2850.035,"action":"Entered and confirmed a TRIM-related command, navigated the drawing with repeated zoom or pan actions, and clicked within the geometry while the trim prompt remained active.","intent":"Continue trimming or inspecting drawing geometry.","app":"AutoCAD","details":"The command line showed TRIM and prompts to select an object to trim or shift-select to extend; no completed trim is confirmed."},{"start_s":2850.035,"end_s":2859.841,"action":"Clicked several drawing elements and adjusted the view while continuing the active TRIM command, ending with the prompt still waiting for an object to trim or extend.","intent":"Select geometry for trimming in the plan drawing.","app":"AutoCAD","details":"The drawing view shifted substantially during the clicks and scrolls."},{"start_s":2859.841,"end_s":2872.075,"action":"Canceled the active trim prompt, invoked a save command, selected a horizontal line, and began a STRETCH operation before canceling it.","intent":"Save the drawing and attempt to adjust line geometry.","app":"AutoCAD","details":"The command history visibly included _qsave and STRETCH; the final state showed the drawing without an active selection."},{"start_s":2872.075,"end_s":2880.001,"action":"Entered and confirmed the TRIM command, dragged across the drawing while selecting trim geometry, then canceled and navigated the view with middle-button clicks and scrolling.","intent":"Modify and inspect the floor-plan linework using Trim.","app":"AutoCAD","details":"The drawing view changed from a close-up to a wider view of the floor plans; the command line ended at a general prompt."},{"start_s":2880.001,"end_s":2886.955,"action":"Entered an offset distance of 9'-10\", then selected and positioned geometry for the OFFSET operation while clicking and dragging near the right side of the plan.","intent":"Create parallel floor-plan geometry at the specified offset distance.","app":"AutoCAD","details":"OFFSET remained active and prompted for an object or side to offset."},{"start_s":2886.955,"end_s":2902.786,"action":"Entered an additional offset distance of 0.5\", canceled a prior operation, restarted TRIM, and dragged across the zoomed drawing while selecting trim regions.","intent":"Trim and adjust the floor-plan linework after applying offsets.","app":"AutoCAD","details":"The view was panned or zoomed during the extended drag sequence, and TRIM remained active at the end."},{"start_s":2902.786,"end_s":2909.353,"action":"Encountered an AutoCAD abort/error transition, then returned to the drawing recovery view showing backup files and both floor-plan drawings.","intent":"Recover or inspect the drawing after AutoCAD stopped responding or aborted.","app":"AutoCAD","details":"Drawing Recovery Manager was visible with backup-file entries and a recovered floor-plan view."},{"start_s":2909.353,"end_s":2913.492,"action":"Navigated the recovered drawing and resized the AutoCAD window, leaving OFFSET active with the prompt to specify an offset distance or choose Through.","intent":"Continue offsetting recovered floor-plan geometry.","app":"AutoCAD","details":"The recovery manager remained open while the drawing was zoomed into the plan."},{"start_s":2913.492,"end_s":2919.766,"action":"Entered an offset distance of 9'-10\", selected or targeted drawing geometry, and indicated the side for the offset with clicks and a short drag.","intent":"Create another parallel line at the specified offset distance.","app":"AutoCAD","details":"OFFSET remained active at the end, prompting for another object to offset."},{"start_s":2919.766,"end_s":2929.567,"action":"Entered a 0.5-inch value, activated Trim, dragged across the drawing, and then undid or canceled the operation.","intent":"Trim or adjust selected plan geometry.","app":"AutoCAD","details":"The drawing remained in the Trim command with a prompt to select objects."},{"start_s":2929.567,"end_s":2943.827,"action":"Canceled the active command, navigated around the plan with clicks, middle-button panning, and scrolling, and briefly initiated Stretch before canceling it.","intent":"Inspect and reposition the drawing while attempting geometry edits.","app":"AutoCAD","details":"The view shifted substantially and ended with a horizontal line selected and the command canceled."},{"start_s":2943.827,"end_s":2953.079,"action":"Reactivated Trim, panned across the plan, and dragged or clicked over several line segments to apply trim selections.","intent":"Trim linework in the floor-plan drawing.","app":"AutoCAD","details":"The Trim prompt remained active while the view moved to another portion of the plan."},{"start_s":2953.079,"end_s":2968.678,"action":"Continued dragging and clicking within the active Trim command while panning and scrolling across the drawing.","intent":"Continue editing and inspecting plan linework with Trim.","app":"AutoCAD","details":"The view moved through multiple regions of the plan; the prompt continued to request objects to trim or extend."},{"start_s":2968.678,"end_s":2974.234,"action":"Clicked several plan segments, briefly initiated Stretch, and then canceled the operation.","intent":"Adjust selected plan geometry.","app":"AutoCAD","details":"A horizontal segment was selected and the command line showed Stretch awaiting a point before cancellation."},{"start_s":2974.234,"end_s":2980.86,"action":"Reactivated Trim, clicked and dragged across plan geometry while panning and scrolling, then canceled the command.","intent":"Trim and inspect floor-plan linework.","app":"AutoCAD","details":"The final view showed the Trim command canceled with the drawing repositioned."},{"start_s":2980.86,"end_s":2999.047,"action":"Activated AutoCAD, entered and confirmed the R command, then panned and zoomed around the drawing while the Trim prompt remained active. Pressed Escape and continued navigating the plan view.","intent":"Navigate and inspect the drawing while working in the active Trim command.","app":"Autodesk AutoCAD 2021","details":"Drawing Recovery Manager was visible on the left; the command line showed Trim prompts before returning to an idle command field."},{"start_s":2999.047,"end_s":3009.034,"action":"Re-entered and confirmed the R command, then dragged to pan across the AutoCAD drawing and repositioned the view while the Trim prompt remained visible.","intent":"Continue navigating the plan view during the active Trim operation.","app":"Autodesk AutoCAD 2021","details":"The drawing view shifted substantially; no completed trim result is visibly confirmed."},{"start_s":3009.034,"end_s":3022.923,"action":"Dragged across the drawing, clicked within the plan, and pressed Escape to cancel the active Trim selection. Saved with Ctrl+S and continued panning and zooming the drawing.","intent":"Cancel the current trim attempt, save the drawing, and inspect another area of the plan.","app":"Autodesk AutoCAD 2021","details":"The command line showed a canceled Trim prompt, then returned to the normal command field."},{"start_s":3022.923,"end_s":3032.888,"action":"Re-entered and confirmed the R command, then dragged to pan and reposition the floor-plan view while the Trim prompt remained active.","intent":"Navigate to another drawing area for the ongoing Trim operation.","app":"Autodesk AutoCAD 2021","details":"The view changed to a zoomed floor-plan region with the Trim selection prompt visible."},{"start_s":3032.888,"end_s":3043.487,"action":"Dragged extensively across the drawing to pan through the plan, clicked near the drawing area, and used middle-button navigation and scrolling. Left the Trim command waiting for the next fence point or object selection.","intent":"Inspect and reposition the plan while continuing the Trim workflow.","app":"Autodesk AutoCAD 2021","details":"The command line showed Trim and fence-point prompts; no completed modification is confirmed."},{"start_s":3043.487,"end_s":3053.897,"action":"Scrolled and middle-clicked to navigate, then dragged to pan across another section of the floor plan and clicked in the drawing. Continued viewing the active Trim prompt.","intent":"Continue inspecting and positioning the drawing for trimming.","app":"Autodesk AutoCAD 2021","details":"The final view showed the Trim prompt asking to select an object or shift-select to extend."},{"start_s":3053.897,"end_s":3063.898,"action":"Navigated around the AutoCAD drawing with middle-button panning and zooming, then dragged across the plan while the Trim command remained active.","intent":"Adjust the drawing view and work on geometry with Trim.","app":"Autodesk AutoCAD","details":"The command line displayed prompts to select objects to trim or shift-select to extend."},{"start_s":3063.898,"end_s":3073.799,"action":"Panned and zoomed across the floor-plan geometry, dragged in the drawing area, and left the Trim prompt active.","intent":"Inspect and modify additional drawing edges using Trim.","app":"Autodesk AutoCAD","details":"The view shifted to show rectangular plan outlines; no confirmed trim result was visible."},{"start_s":3073.799,"end_s":3083.445,"action":"Zoomed and panned through the plan, dragged across drawing geometry, and continued interacting while AutoCAD prompted for objects to trim or extend.","intent":"Continue inspecting and editing the floor plan with Trim.","app":"Autodesk AutoCAD","details":"Rectangular room-like outlines remained visible and no explicit completion message appeared."},{"start_s":3083.445,"end_s":3093.487,"action":"Panned and zoomed to another portion of the drawing, dragged across the geometry, and continued the active Trim operation.","intent":"Work through additional plan edges with the Trim tool.","app":"Autodesk AutoCAD","details":"The command line continued to show the Trim selection prompt."},{"start_s":3093.487,"end_s":3110.09,"action":"Pressed Escape to cancel the active Trim operation, resized and manipulated the AutoCAD window, then selected and dragged drawing geometry; canceled another command before switching focus within AutoCAD.","intent":"Exit the current editing operation and reposition or adjust drawing elements.","app":"Autodesk AutoCAD","details":"The command line showed canceled Trim/Polygon operations and a selected horizontal line with grips before the window changes."},{"start_s":3110.09,"end_s":3116.771,"action":"Returned focus to the main AutoCAD drawing, canceled the prior command, typed L, and confirmed it to start the LINE command; positioned the cursor for the first point.","intent":"Begin drawing a new line in the floor plan.","app":"Autodesk AutoCAD","details":"The command line displayed LINE and prompted for the first point, then the next point or Undo."},{"start_s":3116.771,"end_s":3120.805,"action":"Switched to AutoCAD, canceled an active LINE command, and began another line command after adjusting the command interface.","intent":"Continue drawing or editing linework in the floor plan.","app":"AutoCAD","details":"The drawing remained in model space with the LINE prompt visible."},{"start_s":3120.805,"end_s":3129.675,"action":"Entered the TRIM command, selected or adjusted trimming geometry, and canceled the command after navigating the drawing view.","intent":"Trim unwanted portions of the floor-plan linework.","app":"AutoCAD","details":"The command line showed TRIM and prompted for objects to trim or extend."},{"start_s":3129.675,"end_s":3137.088,"action":"Confirmed the previous command, navigated the drawing, and started a new LINE command while positioning the first point.","intent":"Create additional linework in the floor plan.","app":"AutoCAD","details":"The LINE command remained active with a first-point prompt."},{"start_s":3137.088,"end_s":3147.168,"action":"Entered TRIM, dragged and clicked across the drawing to select or trim geometry, then canceled the command and continued navigating the view.","intent":"Refine floor-plan geometry by trimming selected edges.","app":"AutoCAD","details":"The TRIM prompt asked to select an object to trim or extend."},{"start_s":3147.168,"end_s":3160.423,"action":"Navigated and zoomed the drawing, then initiated COPY and selected multiple objects around the guest-room area.","intent":"Prepare to duplicate selected floor-plan elements.","app":"AutoCAD","details":"The view showed the guest room, open-to-sky area, wash area, and C toilet; COPY was waiting for object selection."},{"start_s":3160.423,"end_s":3170.6,"action":"Continued the COPY operation, selected approximately 43 objects, specified a base point, and began positioning the copied group at a second point.","intent":"Duplicate the selected guest-room floor-plan elements to another location.","app":"AutoCAD","details":"The command line showed COPY with multiple-copy mode and a second-point displacement prompt."},{"start_s":3170.6,"end_s":3182.258,"action":"Adjusted the AutoCAD window, canceled an active command, and selected a guest-room furniture object for rotation.","intent":"Modify the guest-room furniture placement.","app":"AutoCAD","details":"The command line progressed from COPY to ROTATE and ended at object selection."},{"start_s":3182.258,"end_s":3190.467,"action":"Selected the guest-room furniture object, moved it, and began specifying a rotation angle before returning to object selection.","intent":"Reposition and orient the guest-room furniture.","app":"AutoCAD","details":"The furniture appears moved to the right side of the plan and remains selected."},{"start_s":3190.467,"end_s":3199.229,"action":"Selected the same objects and specified a move base point, then dragged the view to a closer area of the guest-room plan.","intent":"Continue repositioning the selected drawing objects.","app":"AutoCAD","details":"AutoCAD showed MOVE with 43 objects found and a displacement preview."},{"start_s":3199.229,"end_s":3210.216,"action":"Zoomed and panned the drawing, then returned to the broader floor-plan view while leaving COPY active at object selection.","intent":"Review the floor plan and prepare another copy operation.","app":"AutoCAD","details":"The view returned to both floor-plan layouts, with the command line showing COPY Select objects."},{"start_s":3210.216,"end_s":3220.581,"action":"Zoomed into the upper-left plan and selected text around the OPEN TO SKY label, leaving multiple objects selected in COPY mode.","intent":"Copy or duplicate selected plan annotation objects.","app":"AutoCAD","details":"The selected OPEN TO SKY text was highlighted; the command line reported two total objects, including one duplicate."},{"start_s":3220.581,"end_s":3230.517,"action":"Specified a copy base point for the selected objects and moved the preview across the zoomed plan while navigating the view.","intent":"Place a duplicate of the selected plan annotation.","app":"AutoCAD","details":"The command line showed COPY with multiple-copy mode and a second-point displacement preview."},{"start_s":3230.517,"end_s":3240.3,"action":"Adjusted the AutoCAD view through window resizing, middle-button navigation, and scrolling while a COPY command remained active; left-clicked and dragged near the lower drawing area without completing the command.","intent":"Navigate the floor plan and continue positioning copied geometry.","app":"AutoCAD","details":"Drawing recovery manager is visible; the command line repeatedly prompts for a second point."},{"start_s":3240.3,"end_s":3249.623,"action":"Navigated and zoomed around the floor plan with middle-button clicks and scrolling, then pressed Escape to cancel the active COPY operation.","intent":"Inspect the plan and cancel the unfinished copy placement.","app":"AutoCAD","details":"The view moves from a broader guest-room area to a close-up of multiple OPEN TO SKY labels."},{"start_s":3249.623,"end_s":3267.705,"action":"Clicked and dragged geometry around the OPEN TO SKY areas, canceled and undid intermediate operations, and left a horizontal line selected while STRETCH remained active; switched focus back to AutoCAD.","intent":"Modify the selected drawing geometry near the labeled openings.","app":"AutoCAD","details":"The command line shows STRETCH and prompts for a stretch point."},{"start_s":3267.705,"end_s":3275.369,"action":"Entered R and confirmed it, then dragged and clicked across the plan; canceled the prior operation and entered L to start a LINE command.","intent":"Switch drawing commands and begin creating or editing linework in the floor plan.","app":"AutoCAD","details":"TRIM prompts appear during the interval, followed by a LINE command prompt at the boundary."},{"start_s":3275.369,"end_s":3283.283,"action":"Confirmed the pending command, navigated and clicked near the OPEN TO SKY rooms, canceled an attempted line, then entered another line command and left it awaiting the next point.","intent":"Draw linework near the room boundaries and labeled openings.","app":"AutoCAD","details":"The command line shows LINE with prompts for the first and next points."},{"start_s":3283.283,"end_s":3287.534,"action":"Confirmed the line command, clicked in the upper OPEN TO SKY area, canceled the line, and typed TR to begin a trim-related command.","intent":"Attempt line placement and transition to trimming nearby geometry.","app":"AutoCAD","details":"The final view shows the OPEN TO SKY labels with the command input containing TR."},{"start_s":3287.534,"end_s":3291.548,"action":"Resized and repositioned the AutoCAD window, canceled the active trim operation, then entered and confirmed the Line command.","intent":"Prepare a drawing command in AutoCAD.","app":"AutoCAD","details":"The drawing remained on the floor plan with multiple OPEN TO SKY labels."},{"start_s":3291.548,"end_s":3298.564,"action":"Adjusted the AutoCAD window and view, canceled the pending line operation, then entered the Line command and left it awaiting the first point.","intent":"Start a line-drawing operation in the floor plan.","app":"AutoCAD","details":"The view was zoomed closely on the floor-plan annotations before returning to the drawing."},{"start_s":3298.564,"end_s":3303.171,"action":"Entered and confirmed a command, clicked and dragged in the drawing, then canceled the active trim operation.","intent":"Interact with and inspect floor-plan geometry while managing drawing commands.","app":"AutoCAD","details":"The view returned to several OPEN TO SKY rooms; no completed geometry change is clearly visible."},{"start_s":3303.171,"end_s":3313.003,"action":"Confirmed the pending command, adjusted the view with window movements and scrolling, then started another Line command and left it awaiting the first point.","intent":"Position the view and begin drawing another line.","app":"AutoCAD","details":"The view shifted from the full plan to a close-up around the room labels and wall lines."},{"start_s":3313.003,"end_s":3320.447,"action":"Entered and confirmed a command, clicked and dragged in the drawing, canceled the active operation, then zoomed out to review the floor plan.","intent":"Inspect the plan at a broader scale after command interaction.","app":"AutoCAD","details":"The resulting view showed guest rooms and multiple OPEN TO SKY labels."},{"start_s":3320.447,"end_s":3325.955,"action":"Opened text editing and replaced the selected room label with “BED ROOM,” confirming the entry.","intent":"Relabel a room in the floor-plan drawing.","app":"AutoCAD","details":"The visible label reads BED ROOM above the existing 10' X 11'6\" dimensions."},{"start_s":3325.955,"end_s":3335.712,"action":"Edited a bedroom annotation and entered the dimension text “12' X 15'2\",” then returned to the drawing view.","intent":"Update the bedroom label with its dimensions.","app":"AutoCAD","details":"The BED ROOM label displays 12' X 15'2\"."},{"start_s":3335.712,"end_s":3344.842,"action":"Selected an annotation and replaced its dimension text with “6'10\" X 4',” confirming the edit.","intent":"Update an open-to-sky area label with its dimensions.","app":"AutoCAD","details":"The upper OPEN TO SKY label displays 6'10\" X 4'."},{"start_s":3344.842,"end_s":3349.598,"action":"Selected another annotation and entered the label “DRESS,” confirming the text edit.","intent":"Name the room in the floor plan.","app":"AutoCAD","details":"The room label displays DRESS."},{"start_s":3349.598,"end_s":3359.889,"action":"Edited the DRESS annotation’s dimensions and entered “7'6\" X 6'10\".”","intent":"Add the dimensions to the DRESS room label.","app":"AutoCAD","details":"The DRESS label displays 7'6\" X 6'10\"."},{"start_s":3359.889,"end_s":3367.693,"action":"Selected another room annotation and entered “A. TOILET,” confirming the edit.","intent":"Name the adjacent room in the floor plan.","app":"AutoCAD","details":"The room label displays A. TOILET."},{"start_s":3367.693,"end_s":3381.605,"action":"Edited the A. TOILET annotation to enter “5' X 11'6\",” canceled the active selection command, and navigated the drawing view until the GUEST ROOM annotation was visible.","intent":"Add the room dimensions and review another area of the floor plan.","app":"AutoCAD","details":"A. TOILET displays 5' X 11'6\"; the final view shows GUEST ROOM 10' X 11'6\"."},{"start_s":3381.605,"end_s":3386.864,"action":"Switched to AutoCAD, entered “BED ROOM,” and confirmed the text edit. Continued clicking while AutoCAD remained in the TextEdit selection prompt.","intent":"Label the bedroom area in the floor plan.","app":"AutoCAD","details":"The drawing shows BED ROOM beside the bed layout."},{"start_s":3386.864,"end_s":3400.889,"action":"Entered and confirmed the bedroom dimensions “14'6\" X 18'.” Clicked repeatedly in the drawing and adjusted the view while the TextEdit command remained active.","intent":"Add the bedroom dimensions to the floor-plan annotation.","app":"AutoCAD","details":"The bedroom label displays 14'6\" X 18\" and the view is zoomed out afterward."},{"start_s":3400.889,"end_s":3408.746,"action":"Entered and confirmed “A TOILET,” then adjusted the drawing view with scroll input and clicks.","intent":"Label the toilet area in the floor plan.","app":"AutoCAD","details":"The toilet area displays A TOILET above the existing 7'2\" X 5'10\" dimension."},{"start_s":3408.746,"end_s":3417.852,"action":"Entered and confirmed the toilet dimensions “10'4\" X 8'.” Used middle-click and scroll actions to reposition the view.","intent":"Add the toilet dimensions to the floor-plan annotation.","app":"AutoCAD","details":"The toilet label displays 10'4\" X 8'."},{"start_s":3417.852,"end_s":3426.963,"action":"Entered “LAWN,” then entered and confirmed “BELOW” to complete the label.","intent":"Label the lower outdoor area in the floor plan.","app":"AutoCAD","details":"The annotation now reads LAWN BELOW above 7'2\" X 5'10\"."},{"start_s":3426.963,"end_s":3436.764,"action":"Entered the lawn dimensions in two parts and confirmed the text as “11'4\" X 1-6'.” Clicked in the drawing after completing the edit.","intent":"Add dimensions to the lawn-below annotation.","app":"AutoCAD","details":"The lawn annotation displays LAWN BELOW with 11'4\" X 1-6'."},{"start_s":3436.764,"end_s":3446.093,"action":"Selected the “OPEN” annotation and edited its text to “OPEN BELOW,” then confirmed the edit.","intent":"Correct the room annotation label.","app":"AutoCAD","details":"Text Formatting mode remained active after confirmation."},{"start_s":3446.093,"end_s":3455.887,"action":"Edited the second line of the “OPEN BELOW” annotation to “15'2\" X 9'6\"” and confirmed the change.","intent":"Update the displayed dimensions for the annotation.","app":"AutoCAD","details":"The drawing visibly showed OPEN BELOW with the new dimensions."},{"start_s":3455.887,"end_s":3464.318,"action":"Selected the “OPEN TO SKY” annotation and replaced its label with “BALCONY,” then confirmed the text edit.","intent":"Rename the annotated area.","app":"AutoCAD","details":"The dimensions below the label remained 7'2\" X 5'10\"."},{"start_s":3464.318,"end_s":3473.903,"action":"Selected the dimensions under “BALCONY” and edited them to “14'6\" X 4'2\",” confirming the text entry.","intent":"Update the balcony dimensions.","app":"AutoCAD","details":"The annotation was still in text-edit mode at the end of the span."},{"start_s":3473.903,"end_s":3486.997,"action":"Exited text editing, zoomed and panned to another portion of the floor plan, and initiated the COPY command with two objects selected.","intent":"Prepare to duplicate selected floor-plan objects.","app":"AutoCAD","details":"The command line showed COPY and prompted for a base point."},{"start_s":3486.997,"end_s":3495.581,"action":"Continued the COPY operation by positioning the view and moving the cursor to specify the base point and displacement for the selected objects.","intent":"Position copied floor-plan elements.","app":"AutoCAD","details":"The command line showed prompts for the base point and second point/displacement; no completed placement was visible."},{"start_s":3495.581,"end_s":3506.678,"action":"Edited the selected DRESS text and replaced its dimensions with “10'4\" X 9'10\",","intent":"Update the room label dimensions.","app":"AutoCAD","details":"Text Formatting was active briefly before returning to the drawing."},{"start_s":3506.678,"end_s":3522.12,"action":"Exited text editing, navigated the floor plan, and initiated the COPY command with multiple objects selected.","intent":"Copy selected floor-plan elements.","app":"AutoCAD","details":"The command line shows COPY and an active object-selection prompt."},{"start_s":3522.12,"end_s":3533.961,"action":"Specified a base point for the selected objects and continued positioning the copy while zooming out to view both floor plans.","intent":"Position a copied group in the drawing.","app":"AutoCAD","details":"The copy command remained active and displayed a second-point/displacement prompt."},{"start_s":3533.961,"end_s":3545.825,"action":"Continued the copy workflow, then started ROTATE on the selected objects and specified a base point and rotation angle of 270 degrees.","intent":"Rotate the selected copied floor-plan elements.","app":"AutoCAD","details":"The command line shows ROTATE with the rotation-angle prompt active."},{"start_s":3545.825,"end_s":3550.344,"action":"Started MIRROR for the selected objects and specified the first point of the mirror line, then moved toward the second point.","intent":"Create a mirrored version of the selected elements.","app":"AutoCAD","details":"The MIRROR command was active with two objects found."},{"start_s":3550.344,"end_s":3555.159,"action":"Specified the second mirror-line point, accepted the default to retain source objects, and began selecting objects for MOVE.","intent":"Finish mirroring and reposition the resulting geometry.","app":"AutoCAD","details":"The mirrored upper door geometry is visible; MOVE is active with an object-selection prompt."},{"start_s":3555.159,"end_s":3569.563,"action":"Repositioned and resized the AutoCAD window, selected two drawing objects, and initiated a MOVE operation while adjusting the view around the floor plan.","intent":"Move selected floor-plan geometry to a new position.","app":"AutoCAD","details":"The command line remained at MOVE with base-point and second-point prompts."},{"start_s":3569.563,"end_s":3577.208,"action":"Canceled the prior prompt, selected the DRESS room label, and continued the MOVE selection workflow.","intent":"Select and reposition the DRESS annotation.","app":"AutoCAD","details":"The DRESS text was visibly highlighted and the command line showed MOVE Select objects."},{"start_s":3577.208,"end_s":3583.094,"action":"Selected additional drawing content and used SCALE on two found objects, specifying a base point before leaving the scale command active.","intent":"Scale selected floor-plan elements.","app":"AutoCAD","details":"The command line showed SCALE and a base-point prompt."},{"start_s":3583.094,"end_s":3594.289,"action":"Specified a scale base point, zoomed out to review more of the floor plan, and left the scale-factor prompt active.","intent":"Review the scaled drawing in a wider view and complete scaling.","app":"AutoCAD","details":"The full upper floor-plan area became visible, including BED ROOM, DRESS, A. TOILET, and OPEN TO SKY."},{"start_s":3594.289,"end_s":3612.376,"action":"Adjusted the view, saved the drawing with QSAVE, and initiated ROTATE on two selected objects while navigating the broader plan.","intent":"Save edits and rotate selected floor-plan geometry.","app":"AutoCAD","details":"The command line showed ROTATE with two objects found and a selection prompt."},{"start_s":3612.376,"end_s":3623.11,"action":"Specified a rotation base point and adjusted the rotation angle for the selected objects, leaving the ROTATE operation in progress.","intent":"Rotate the selected drawing elements.","app":"AutoCAD","details":"The command line prompted for the rotation angle; a door-like arc appeared repositioned to the right of the plan."},{"start_s":3623.11,"end_s":3627.751,"action":"Activated AutoCAD and continued the MIRROR command by selecting objects and specifying a mirror line; reached the prompt asking whether to erase source objects.","intent":"Mirror selected floor-plan geometry while deciding whether to retain the originals.","app":"AutoCAD","details":"Drawing G+1 [hidden] remained visible."},{"start_s":3627.751,"end_s":3635.362,"action":"Chose No at the erase-source prompt, then initiated MOVE and selected objects for relocation.","intent":"Keep the mirrored source geometry and reposition selected drawing elements.","app":"AutoCAD","details":"The command line showed MOVE with object selection active."},{"start_s":3635.362,"end_s":3645.407,"action":"Confirmed the selection and specified a base point and displacement for MOVE, shifting three selected objects to the right side of the plan.","intent":"Relocate selected floor-plan components within the drawing.","app":"AutoCAD","details":"The moved geometry appeared beside the existing plan while MOVE remained active."},{"start_s":3645.407,"end_s":3656.136,"action":"Completed the move, then started COPY and selected one object for duplication.","intent":"Begin duplicating a drawing element after repositioning the selected geometry.","app":"AutoCAD","details":"The command line showed COPY with one object found."},{"start_s":3656.136,"end_s":3675.164,"action":"Specified a copy base point and multiple displacement points while zooming and navigating the drawing; left COPY active at a detailed floor-plan view.","intent":"Create repeated copies of the selected floor-plan element.","app":"AutoCAD","details":"COPY mode was Multiple and the command awaited another displacement or exit."},{"start_s":3675.164,"end_s":3685.906,"action":"Exited the copy operation, selected two objects, started SCALE, specified a base point and scale factor, and then erased one object.","intent":"Adjust the size of selected drawing geometry and remove an unwanted object.","app":"AutoCAD","details":"The final command line reported _erase 1 found."},{"start_s":3685.906,"end_s":3691.683,"action":"Activated AutoCAD and continued the LINE command by placing a segment near the doorway area, then adjusted the dynamic input and canceled the active command.","intent":"Modify linework in the floor plan.","app":"AutoCAD","details":"The drawing remained in the LINE command with a new segment preview visible before cancellation."},{"start_s":3691.683,"end_s":3701.185,"action":"Entered the R command and confirmed it, then interacted with the drawing and command line; zoomed to the bedroom and dressing-room area and issued a save command before canceling.","intent":"Navigate and save the current drawing while preparing another edit.","app":"AutoCAD","details":"The view changed from a close-up doorway area to a larger view labeled BED ROOM and DRESS; the command line showed _qsave."},{"start_s":3701.185,"end_s":3708.09,"action":"Selected a rectangular area near the bedroom doorway and began the SCALE command, leaving AutoCAD waiting for the opposite corner of the selection window.","intent":"Select and scale drawing geometry near the doorway.","app":"AutoCAD","details":"A blue selection window was visible with the prompt “SCALE Select objects: Specify opposite corner.”"},{"start_s":3708.09,"end_s":3723.076,"action":"Completed the selection and navigated the plan with zoom and pan gestures, then started ROTATE and selected one object; the view zoomed out to show both floor plans and AutoCAD waited for a rotation base point.","intent":"Transform a selected floor-plan element and inspect its placement.","app":"AutoCAD","details":"The command line showed ROTATE with one object found and “Specify base point.”"},{"start_s":3723.076,"end_s":3731.526,"action":"Set a rotation base point and adjusted the rotation angle with orthographic tracking, leaving the selected object in a rotation preview state.","intent":"Rotate the selected drawing element to a specified orientation.","app":"AutoCAD","details":"The command line showed “ROTATE Specify rotation angle or [Copy Reference] <180>:” and the cursor displayed an orthographic angle readout."},{"start_s":3731.526,"end_s":3736.204,"action":"Started MIRROR on the selected object, specified the first and second points of the mirror line, and reached the prompt asking whether to erase the source objects.","intent":"Create a mirrored copy of the selected drawing element.","app":"AutoCAD","details":"The “Erase source objects? [Yes No] <No>:” prompt was visible, awaiting confirmation."},{"start_s":3736.204,"end_s":3743.418,"action":"Switched to the AutoCAD drawing, manipulated the view and window, and initiated a MOVE operation after selecting drawing objects.","intent":"Modify the placement of selected plan elements.","app":"AutoCAD","details":"The command line showed MOVE with objects selected and awaiting a base point."},{"start_s":3743.418,"end_s":3759.805,"action":"Continued the MOVE operation by specifying a base point and moving the selected object while zooming and panning around the floor plan.","intent":"Reposition selected drawing geometry.","app":"AutoCAD","details":"The command line progressed from specifying the base point to specifying the second point."},{"start_s":3759.805,"end_s":3768.246,"action":"Switched from the completed move workflow to ROTATE, selected drawing content, and reached the base-point prompt while viewing both floor plans.","intent":"Rotate selected plan elements.","app":"AutoCAD","details":"The command line displayed ROTATE and requested a base point and rotation angle."},{"start_s":3768.246,"end_s":3781.939,"action":"Continued the MOVE workflow with selected plan geometry, zooming into the upper-floor rooms and positioning the cursor for a second point before cancelling or leaving the command active.","intent":"Adjust the position of selected drawing elements.","app":"AutoCAD","details":"The view changed from the overall plans to a close-up showing the bedroom, toilet, and balcony areas."},{"start_s":3781.939,"end_s":3789.562,"action":"Started SCALE on selected objects, specified a base point, and left the command waiting for a scale factor while zooming back to the overall plans.","intent":"Resize selected drawing elements.","app":"AutoCAD","details":"The command line showed SCALE and prompted for a scale factor or Copy/Reference."},{"start_s":3789.562,"end_s":3807.502,"action":"Entered TRIM, selected or dragged across drawing areas, zoomed and panned the plans, and left TRIM active awaiting another object selection.","intent":"Trim or extend floor-plan linework.","app":"AutoCAD","details":"The command line displayed the TRIM prompt to select an object to trim or shift-select to extend."},{"start_s":3807.502,"end_s":3819.678,"action":"Entered a trim command, dragged and clicked around the floor-plan boundaries, and adjusted the view while AutoCAD prompted for objects to trim or extend.","intent":"Modify floor-plan linework using Trim.","app":"AutoCAD","details":"The drawing view ended focused on the balcony, open-below, lawn-below, and open-to-sky areas."},{"start_s":3819.678,"end_s":3831.221,"action":"Canceled the active trim operation, then initiated a stretch command and dragged a selected vertical line while resizing and repositioning the AutoCAD window.","intent":"Adjust floor-plan geometry with Stretch.","app":"AutoCAD","details":"The command line showed an active STRETCH operation with a selected vertical segment and a dynamic distance readout."},{"start_s":3831.221,"end_s":3844.945,"action":"Entered Trim again, dragged and clicked across the floor-plan edges, zoomed or panned to review the drawing, and canceled the stretch-related prompt.","intent":"Trim or inspect floor-plan boundaries.","app":"AutoCAD","details":"The view shifted from the open-below/lawn-below area to a broader view including the bedroom, balcony, toilet, and open-to-sky labels."},{"start_s":3844.945,"end_s":3850.353,"action":"Re-entered Trim, clicked and dragged around the lawn-below and adjacent room boundaries, and zoomed out to review the surrounding plan.","intent":"Modify and inspect floor-plan linework with Trim.","app":"AutoCAD","details":"The command line continued to prompt for objects to trim or extend."},{"start_s":3850.353,"end_s":3858.86,"action":"Scrolled and panned the drawing, re-entered Trim, selected or clicked near the open-below and lawn-below regions, then canceled the active prompt and issued a save shortcut.","intent":"Continue trimming and save the drawing.","app":"AutoCAD","details":"The final view was zoomed toward the balcony and open-below area, with Trim still visible in the command line."},{"start_s":3858.86,"end_s":3871.077,"action":"Panned and zoomed to the upper bedroom layout, started a DIMLINEAR command, selected an extension-line origin, and positioned a horizontal dimension above the plan.","intent":"Add a linear dimension to the floor plan.","app":"AutoCAD","details":"The displayed dimension measured 26'-6\" above the bedroom/open-to-sky layout."},{"start_s":3871.077,"end_s":3884.699,"action":"Switched to AutoCAD, adjusted the window repeatedly, and navigated the drawing while a DIMLINEAR command remained active; ended with the floor plans visible and the command prompt reset.","intent":"Work within the AutoCAD floor-plan drawing and manage the active dimension command.","app":"AutoCAD","details":"The view changed from a close-up first-floor plan to both ground- and first-floor plans."},{"start_s":3884.699,"end_s":3897.366,"action":"Switched briefly through Explorer and the recorder, returned to AutoCAD, and edited annotation text to enter “FIRST FLOOR PLAN” followed by Enter.","intent":"Rename or update a floor-plan annotation in the drawing.","app":"AutoCAD","details":"The edited text is visible near the first-floor plan, with the drawing entering TEXTEDIT mode."},{"start_s":3897.366,"end_s":3905.706,"action":"Returned to AutoCAD, zoomed and navigated around the drawing, then selected and erased one annotation object.","intent":"Clean up or adjust floor-plan annotations.","app":"AutoCAD","details":"The command history shows “_erase 1 found,” and the floor-plan labels remain visible."},{"start_s":3905.706,"end_s":3915.706,"action":"Zoomed and panned around the floor plans, selected the first-floor plan geometry, and initiated a MOVE operation with the objects selected.","intent":"Reposition the first-floor plan within the drawing layout.","app":"AutoCAD","details":"The first-floor plan is highlighted in blue and the command line requests object selection or placement."},{"start_s":3915.706,"end_s":3931.372,"action":"Navigated and zoomed out, saved the drawing with QSAVE, then zoomed back into the first-floor plan.","intent":"Save the current drawing and inspect the first-floor layout.","app":"AutoCAD","details":"The view ends on a close-up of the first-floor rooms and dimensions."},{"start_s":3931.372,"end_s":3941.162,"action":"Started the LINE command, zoomed and panned across the first-floor plan, and left the command active while positioning the cursor for the first point.","intent":"Draw a line element in the first-floor plan.","app":"AutoCAD","details":"The command line repeatedly shows “LINE Specify first point,” with the view focused on bedroom, dressing, toilet, and corridor geometry."},{"start_s":3941.162,"end_s":3951.302,"action":"Switched to AutoCAD, entered commands, navigated the floor plan, and performed trim-related selections before canceling and adjusting the view.","intent":"Edit and inspect floor-plan geometry.","app":"AutoCAD","details":"The drawing remained in a trim command state with visible room and doorway geometry."},{"start_s":3951.302,"end_s":3960.631,"action":"Confirmed the command, zoomed and panned the drawing, then initiated the OFFSET command and clicked around the upper-floor plan to select objects and specify offset locations.","intent":"Offset selected floor-plan elements.","app":"AutoCAD","details":"The command line showed OFFSET with prompts to select an object and specify the side."},{"start_s":3960.631,"end_s":3972.775,"action":"Continued selecting points for repeated offsets, producing a set of parallel stair lines, then canceled the offset operation and zoomed out to review both floor plans.","intent":"Create and review repeated stair geometry.","app":"AutoCAD","details":"The upper-floor stair area visibly gained multiple evenly spaced lines."},{"start_s":3972.775,"end_s":3984.824,"action":"Exited the prior operation, navigated the drawing, and started the LINE command by clicking to specify a first point near the stair area.","intent":"Begin drawing a line in the floor plan.","app":"AutoCAD","details":"The command line visibly displayed LINE Specify first point."},{"start_s":3984.824,"end_s":4000.765,"action":"Selected drawing objects and used COPY in multiple mode, specifying a base point and displacement to duplicate stair-related geometry; then canceled the active operation and adjusted the view.","intent":"Duplicate floor-plan stair elements.","app":"AutoCAD","details":"The command line showed COPY with multiple mode and prompts for base and second points."},{"start_s":4000.765,"end_s":4007.067,"action":"Opened Save Drawing As, confirmed the existing G+1 PLAN@02 drawing name and saved the file, returning to a zoomed-out view of the ground- and first-floor plans before switching away.","intent":"Save the edited AutoCAD drawing.","app":"AutoCAD","details":"The Save Drawing As dialog showed the Documents folder and filename G+1 PLAN@02; the title bar afterward showed the drawing saved in Documents."}],"summary":"Developed and edited a two-level residential floor plan in AutoCAD, including walls, offsets, trims, furniture, annotations, room labels, dimensions, stairs, and copied/mirrored elements. Saved the completed drawing as G+1 [hidden]"}